narrate the steps in implementing
The 'mode analysis' study type could solve the corresponding wavenumbers for specific operating frequencies. Then you can plot the points, i.e. (k, f), in the dispersion curves. Any way, try the 'mode analysis' study. Hope it helps.
The value of the average RMSE in my study is 0.523 for training data and 0.514 for testing. I have used 90% data for training and 10% for testing. However I am getting higher RMSE average, is this...
05 April 2024 2,942 1 View
Hi Everyone I'm looking to find the right research topic on additive manufacturing (3D printing or 4D printing) for biomedical, defense, and robotics applications. Can anyone suggest any...
15 November 2023 7,967 3 View
I have prepared a research article about in-app advertising. Considering the word limit and the theme of my paper, I believe that the 'International Journal of Electronic Commerce' is suitable for...
10 September 2023 8,601 2 View
I have made a study in the area of mobile advertising and my manuscript has around 15,000 words. I am trying hard to concise the word length but it is affecting the quality of my paper. Please...
27 June 2023 6,241 3 View
You can suggest some literature too
17 March 2022 1,732 4 View
Hi, I have been awarded the DBT-CTEP travel grant to attend the conference "64th Annual Meeting of the Biophysical Society" in San Diego which is going to be held between 15th to 19th February,...
22 January 2020 6,661 1 View
We are testing a semiconductor board around -60 C to -50 C. We want to make sure it doesn't frost at those low temperatures. The equipment we use may not have a humidity controller. We are looking...
29 April 2019 1,209 1 View
After setting up 100 uL of 10000 cells/mL of the HCT-116 colorectal cancer cell line, we notice that when we place 40 uL of water in the pockets between wells, that our cells grow to about half...
15 August 2018 1,011 2 View
It is well known that bonding between Streptavidin (STV) and biotin is very strong. As a part of my experiment I would like to check if STV binds to biotin which is attached to PEG. The surface...
19 July 2018 1,635 3 View
I am trying to measure stiffness of red blood cells in RPMI using AFM force spectroscopy method. In literature, the typical indentation of RBC at a force of 500pN is 500nm. But in my case I see...
10 July 2018 7,958 5 View
I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...
13 August 2024 9,795 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
How can I define dispersion for salt in Eclipse in a low salinity water flooding code? how can I active interactions between tracer and polymer in Eclipse? Please let me know if you have any idea.
05 August 2024 1,218 1 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...
29 July 2024 5,015 1 View
Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco
29 July 2024 2,163 1 View
Dear all, I have noticed, as the ZnO content increases, the Raman intensity at 100cm-1 also increases. However, there is a peak nearby at 130 cm-1, which I could not find in any paper related to...
28 July 2024 5,410 1 View
In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?
28 July 2024 2,988 0 View
Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...
26 July 2024 9,156 2 View