Which SAR dataset to use for generating coherency matrix and performing target decomposition (Description) ?

Working on chandrayaan-2 DFSAR data, there are three datasets available: 1) Slant range image data product: The slant range complex image file. Each pixel is represented by two 4-byte floating...

02 March 2021 8,481 3 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

What test should I use to compare two or three means, if data is not normally distributed but sample size is > 30 in each group?

I personally feel this as a most confusing question. As per my understanding, if sample size is > 30, and sample is skewed, we can still use paramteric approach, as it will follow Z...

01 March 2021 1,587 6 View

How to design a boost converter for a mppt controller?

I have a doubt on how to select the inductor and capacitor value when I want to implement MPPT controller. This is because we always take a maximum output voltage and current but in this case, we...

28 February 2021 3,637 2 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View

Efficiency of Proximity Feed Patch Antenna ?

Greetings to all of You! I have searched some research papers for the designing of a proximity coupled patch antenna. Researchers are talking about the impedance bandwidth of the antenna but...

24 February 2021 7,662 3 View

Please help in identification of this insect?

This insect is minute in size around 1 mm and not clearly visible with naked eye.

22 February 2021 5,907 11 View

How to calculate refractive index (n and kvalue) against energy (in eV) data for alloyed nanomaterials through Independent Phase Approximation method?

Suggest me the method or some other software to calculate the above said data for nanoparticles.

21 February 2021 3,350 7 View

How to find the air side pressure drop in a spiral fin tube bundle cross flow heat exchanger?

How to find the air side pressure drop in a spiral fin cross flow heat exchanger? The pressure difference at the inlet and outlet is very low compared to the experimental results, which I...

18 February 2021 1,109 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View