How can i get the total moment of inertia of RC section in abaqus ??
Maybe you can calculate it starting from the definitions
http://www.egr.msu.edu/software/abaqus/Documentation/docs/v6.7/books/usb/default.htm?startat=pt06ch24s02alm21.html
Thank you very much, but i use version 6.13 so i can`t find Special in Property or Interaction module
I`m conducting a parametric study using FE abaqus on RC beam shear strengthened with externally side-bonded CFRP. The optimum length which i get is 0.36L, where L is the beam length. Is this...
05 June 2016 3,059 2 View
I made finite element model of RC beam shear strengthened with externally bonded FRP. The FE curve agrees with that of experimental as shown in attached photo but the de-bonding of FRP from...
04 May 2016 6,421 6 View
My model is done using ABAQUS i`m modelling 3D RC beams shear strengthened with FRP. The figure attached shows a comparison between FE and experimental results which is the black dotted...
03 April 2016 6,248 3 View
My model is done by ABAQUS which is shear strengthening of RC beams with externally bonded FRP. I`m using tangential surface to surface interaction where the inputs are the shear stress limit...
03 April 2016 3,906 4 View
I`m using ABAQUS in my FE model which is shear strengthening of RC beams with externally bonded FRP. I`m using tangential surface to surface interaction where the inputs are the shear stress...
03 April 2016 8,803 12 View
I`m made a 3D model of RC beam externally bonded with FRP sheets The problem is in contact between FRP and concrete I`m using surface interaction. i tried a lot of models such as cohesive model...
02 March 2016 9,223 0 View
I am modeling the bond between FRP and concrete using cohesive interface element. I am using ABAQUS software. I don`t know what this error means ??
02 March 2016 1,014 0 View
when i decreased the mesh size in modeling of RC beam in abaqus the beam became stiffer in the elastic zone i don`t know why ??
01 February 2016 2,443 8 View
My model is 3D reinforced concrete beam in ABAQUS software. I knew one reason which may be the development length of longitudinal steel. but i want to know if there are any other reasons because...
01 February 2016 6,252 5 View
i make model in unsaturated expansive soil with coupled pore fluid and stress analysis. in manual the part is created by orphan mesh feature how can i do this and why?
01 February 2016 4,492 7 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View
Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...
06 August 2024 666 4 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View