12 December 2018 1 7K Report

Annulus model.

More Saad Najeeb's questions See All
How experimentally calculated the performance of flat plate collector?

Solar flat plate collector.

01 February 2019 4,731 3 View

How simulate the bubble motion in tube using ANSYS?

Bubble flow into pipe.

01 February 2019 1,370 4 View

How manufactured simple U-tube manometer to measure pressure difference?

U-tube manometer.

01 February 2019 4,127 2 View

How experimentally calculated flat plate solar collector efficiency?

Solar collector efficiency.

01 February 2019 7,884 3 View

How calculate experimentally the efficiency of flat plate collector? What's the limit it?

Solar flat plate collector.

01 February 2019 7,656 3 View

What's the parameters of solar collctor performance?

Flat plate solar collector.

01 February 2019 7,903 7 View

Can anyone help me to find papers for air flow in finned wavy channel?

Finned wavy channel.

01 February 2019 3,456 1 View

What's the range of coefficient h in natural and forced convection?

Mixed heat convection to air.

31 December 2018 3,552 9 View

What's the range of Nu number in forced convection for liquids?

Forced convection heat transfer.

31 December 2018 5,589 8 View

What's the suitable book for finte volume method?

Finite volume method.

31 December 2018 7,240 6 View

Similar questions and discussions
Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

What is the error of the Txy diagram?

Hi, I know the attached Txy diagram has an error but can't figure it out. Could you please look at the diagrams and explain it to me?

23 February 2021 4,239 1 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close