Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How to find the capacitive response frequency from the impedance plot?

I have done electrochemical impedance by using cyclic voltammetry for one organic material. from that, I plotted bode diagram. but actually, I am very confused about how to find the capacitive...

18 February 2021 3,023 3 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View

How can we maintain the two different DC high voltages of same polarity between parallel electrodes inside the vacuum separated by few millimeter?

I am trying to maintain two different high DC voltages of same polarity (either positive or negative) between two parallel electrodes separated by 500 um inside the vacuum. However, what I found...

21 December 2020 1,735 3 View

How to segregate electrode-dielectric and dielctric-dielctric interface polarization after Capacitance VS Freq. measurement using impedance analyzer?

After measuring the capacitance vs frequency for my MIM capacitor consisting of alternate layers of TiO2 &Al2O3 , there is a rise in capacitance value of ~ 20-160 nF at 100 hz, starting to...

17 December 2020 7,786 3 View

How to evaluate area under the discharge curve by using Origin software?

In case of Galvanostat charge-discharge, the discharging time used to evaluate the specific capacitance using following relation: C=I*t/m*dV. But when it comes to capacity, the area under the...

25 November 2020 1,856 1 View

How to structure a Knowledge Management model, to strengthen research and improve educational quality in higher education institutions?

22 November 2020 8,558 9 View

Temporal noise analysis CMOS APS?

I was reading the paper "Analysis of Temporal Noise in CMOS Photodiode Active Pixel Sensor" but I am a bit puzzled about noise calculation during integration. In particular, can someone explain...

15 October 2020 9,597 3 View

What is relation between conductivity and capacitance ? What will be the solution of given problem ?

Consider perfect metallic conductors (red and blue) Of cross-section shown in the figure (the cross-section is centered at x = O). Let the length Of this conductor be 'L' (oriented along...

29 September 2020 2,276 4 View

How to find/make ADS or Spice model of MACOM Varactor diode MA46H071/MA46H201?

Hi, I am looking for ADS/Spice model of macom varactor diode model MA46H071/MA46H201. In the manufacturer website only the ADS model of MA46H120 is available. I do have the datasheets of all...

27 August 2020 3,534 3 View