How to draw the layout of the CNTFET-based standard quaternary inverter using Synopsys HSPICE ?

Ajay Rupani @Ajay-Rupani

12 September 2023 0 1K Report

How to draw the layout of the CNTFET-based standard quaternary inverter using Synopsys HSPICE?

Badges
Science topic

Similar topics
Education
Students

More Ajay Rupani's questions See All

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

How effective has the United Nations been in addressing the conflict and its consequences?

After World War, we have seen the formation of the United Nations. The sovereign body for peacekeeping but with regards to the Russia-Ukraine war it is visible that the UN seems to be ineffective...

18 July 2024 4,674 4 View

What are the main obstacles to achieving a ceasefire or peace agreement between Russia and Ukraine?

It has been a quite long time since the Russia and Ukraine war has been going on and if we see the context of Geopolitics and International Relations we don't see a mediation between the two...

18 July 2024 6,737 4 View

What are the effects of prolonged heat stress on leafy vegetables like lettuce and cabbage?

Effect of heat stress on leafy vegetables

23 June 2024 5,572 3 View

Why there is a frequent raster operation failure amid Hydrological Analysis using LiDAR based 5m DEM in the ArcGIS 3.0.1, ArcGIS 10.8?

I am facing continuous raster operation failures amid Hydrological Analysis. It is very rare that the software ArcGIS 3.0.1 and older versions performs the operation properly if putting DEM 5m in...

10 June 2024 1,963 0 View

Is there any technique which can help in determining sugar concentration in water?

"I want to determine the concentration of a series of sugar solutions. I tried to use refractometry, but the concentration is very low and the difference between the refractive index (RI) values...

29 May 2024 2,464 9 View

"Range chek error" problem in DSSAT Model?

I was previously using the DSSAT version 4.7 in my PC. Now, I have installed the DSSAT v4.8. Whenever I am trying to simulate the experient is shows "Range chek error". This problem exist even...

13 May 2024 5,894 0 View

What should be the End Time, velocity and other settings in ANSYS Workbench Explicit Dynamics to simulate Quasi-static compression?

I am trying to model a quasi-static compression of a complex structurAl geometry. The experiment was done at 2 mm/min of loading. I am using ANSYS Explicit Dynamics. I’m also using Automatic Mass...

20 April 2024 2,934 4 View

Which lab in India does levels of inflammatory mediators like:IL-17, IL- 6,TNF- alpha, Adiponectin, Leptin?

These tests are required for research purpose. Cost for these tests and contact numbers are required

15 April 2024 7,955 1 View

Cross-linking density and swelling ratio in the reaction solvent should be provided. What does it mean?

Cross-linking density and swelling ratio in the reaction solvent should be provided. What does it mean? Can you explain?

21 March 2024 5,571 1 View

How to draw the five chelate rings of [Co(EDTA)]- on this picture?

Is this circle one of the rings?

03 August 2024 5,988 0 View

How to make overlapping p-h diagram in EES?

I want to draw ph diagram using Engineering equation solver EES for refrigerant R134a and R1234fy and some other. I don't know how to draw the multiple ph diagram on same dome or overlapping to...

30 July 2024 647 7 View

What does an additional peak in FTIR between 3100 and 3300 nm affect the quality of the material, benzethonium chloride USP??

I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...

16 July 2024 6,918 7 View

How to draw photon-magnon coupling color plot in origin?

Please help me in plotting the photon-magnon coupling plot as shown below

14 July 2024 1,632 1 View

The criterion about maximally localized wannier function?

I heard that as the value of "num_iter(tag in wannier 90)" is higher, spread of Wannier function(=WF) is gradually lower in wannier 90. If so, is this procedure that minimize the spread of WF...

13 July 2024 4,608 0 View

Taking a cut line through deck build in silvaco?

Hi everyone hope your all doing good. I’ve been looping my scripts and am trying to take a cut line of the conduction band energy with respect to y for each loop. Basically, I want to take a...

03 July 2024 9,134 1 View

Is there a thin line between cultural and ethnic entrepreneurship?

My feeling is that there is - but where does one draw distinction.

01 July 2024 3,716 4 View

Thin DNA gel loading sample tips?

I have a 0.25mM thick gel and I am having trouble cleaning out the wells to ensure constant sample application. I usually use a thin syringe to get into the wells and rinse them out with running...

01 July 2024 2,124 2 View

Could anyone recommend software for drawing the physical structure of nanoparticles?

I am looking for professional software to draw the physical structure of nanoparticles or vesicles, not the chemical structures for which we use ChemDraw, but the actual physical structures,...

23 June 2024 1,292 3 View

Drawing fullerene more than 60 carbon?

I have ChemDraw 22.2.0 and I want to draw PC70BM but I just found C60 and less in the templates so, any one can help me ?

18 June 2024 3,098 3 View