"Range chek error" problem in DSSAT Model?

14 May 2024 0 6K Report

I was previously using the DSSAT version 4.7 in my PC. Now, I have installed the DSSAT v4.8. Whenever I am trying to simulate the experient is shows "Range chek error". This problem exist even with the experiments which are saved already in the model.

Badges
Science topic

Similar topics
Correction

More Ajay Mohan's questions See All

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View

What is the method of removing RNase contamination from a filter paper surface?

I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...

12 February 2021 3,926 3 View

What is causing the raw fluorescence to be negative?

Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...

09 February 2021 4,642 3 View

Regarding immunology, transmissivity, herd immunity and vaccines in Sars CoV-2?

This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....

08 February 2021 8,321 3 View

How can I enter the load increment values to the Abaqus?

In Abaqus I know that there are two methods for incrementation (Automatic and fixed incrementation). I want to control the incrementation by myself. I want to input the values of load increment...

03 February 2021 6,943 3 View

Distortion problem in Abaqus explicit?

Dear all. I'm modeling the RC column with cyclic displacement by Abaqus-Explicit. The concrete model used Concrete Plastic Damage model. However I'm facing with a error about the excessive...

01 February 2021 7,726 1 View

I am finding a lot of cellular debris in the culture flask? What are the reason behind it?

I am facing a problem that cellular debris observed in my SHSY5Y cells. I have seeded the cells in DMEM media with 10% FBS in T-25/ 60mm dish (antibiotic used PEN-Strepand gentamycin). I have also...

17 January 2021 3,074 3 View

What is the reason for discontinued Stage II fatigue crack growth in pearlitic steel?

Conventionally, the process of Stage II fatigue crack growth is governed by Paris law with less microstructural effect. When fatigue crack growth test was carried out for pearlitic steels ( both...

03 January 2021 7,075 3 View

Anyone have any knowledge about the authenticity of the European Journal of Humanities and Social Sciences - (EJ-SOCIAL)?

https://ej-social.org/index.php/ejsocial

30 December 2020 6,845 3 View

Analysis and implementation of Kalman filter in fixed-point arithmetic?

I would like to implement a Kalman filter for tracking applications for IoT nodes. I cannot do floating point on our nodes but only fixed point. Could you recommend some good references?

23 December 2020 4,813 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

My silica gel column dried can I somehoe save the trapped matter?

I tried to separate my substance from a protein in a sillica gel column. By mistake, it dried and cracked. Can I save the trapped substance? Can I repack it ,or at least elute all of the trapped...

22 February 2021 1,789 3 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View