How to do FE analyse of aluminium and steel diffusion bonding?

More Chitaranjan Pany's questions See All

What is an appropriate measure of multivariate function bias towards any of its input variables ?

This is in context of the objective function of a multivariate optimization problem say, f(a,b,c). I am looking for a "measure" for the degree of bias of f(a,b,c) towards any of the input variables.

15 November 2022 7,522 4 View

Can anyone suggest modifications in this circuit intended for power supply ripple filtering ?

Hi, I have a design for source-follower low pass filter which I intend to use with a switched mode power supply. I simulated the circuit in NI Multisim, and for square wave ripple voltage of...

03 January 2019 3,261 9 View

How to model diffusion bonding of impeller vane by FEA ?

literature, FE modelling / analysis, failure

15 September 2018 6,865 1 View

Glutamatergic or GABAergic or dual phenotype neurons ?

Are they any specific methods for developing either glutamatergic or GABAergic or dual phenotype hippocampal neurons from primary hippocampal neurons? Thanks in Advance

12 April 2016 1,697 2 View

Suitable human neuronal cell line for neurotoxicity assay?

I'm looking for a suitable human neuronal cell line for neurotoxicity or neuroprotection screening. Which human neuronal cell model is best for high throughput screening? Can anyone help?

30 September 2015 8,108 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Can we isolate microplastic from sludge sample without using vacuum filter..?

isolation of microplastic from sludge sample using centrifugation ..

23 July 2024 6,418 0 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

Raheem Al-Sabur

COMSOL Software can help you in this purpose

Please see

https://www.comsol.com/forum/thread/105841/inter-diffusion-between-two-pure-metal

Bhavana U.

Hi Chitaranjan Pany ,

you can use ABACUS software for this purpose.

It is easy to learn and with in two weeks time you can model your diffusion bonded joint.