Citation on LaTeX: How to include apa package from the scratch, step by step?

Hello dear readers and researchers, I am a beginner user of Tex Maker. How can I use packages that run citation on LaTeX?

20 January 2021 5,605 3 View

How to allocate separate parts of a LaTex document to several distinct parts in a uniform file?

Hello dear readers and researchers, I have begun learning La-Tex and I want to divide the main file into several section in separate sub sections of a uniform La-Tex project (pardon me for that...

17 January 2021 5,559 1 View

Can you help me in matlab code for calculation solubility of essential oil in super critical CO2?

#super critical CO2 #Matlab code #extraction #thermodynamic

07 December 2020 5,318 1 View

What's your recommendation for high performance, yet stable, organic or inorganic HTM used in perovskite solar cells?

I'm looking forward to a low cost efficient and stable material for hole transporting layer in perovskite solar cell. My light harvester layer is a Cs2AgBiBr6 , band alignment of mentioned double...

06 April 2020 5,046 3 View

What are the thermodynamic equations of crystalline polymers dissolution like cellulose in ionic liquids?

01 January 2019 9,994 3 View

I need some Indian ISI journals in the field of management, marketing, finance & banking. Anyone can give me some names?

Due to recent sanctions, Iranian researchers have been relatively banned to publish any ISI paper in international Journals. Therefore, I wanted to publish my papers in Indian ISI journals. Maybe...

19 December 2018 9,233 2 View

If we use a cone crusher instead of a tank in a rock picker machine, pouring crushed stones will destroy the soil texture?

in all of the rock pickers we loose farm capacity because of fill up an discharge of stones in the other where i want to know that's useful to use cone crusher instead of a tank.

17 February 2018 5,287 2 View

Hi, i want to know is there any rock picker connected to Stone breaker to change Stones to soil in all over the world?

13 September 2017 1,915 2 View

How to interpret the difference between EEG-EMG time lag, cortico-muscular conduction time and LFP-EEG time lag for hand muscles?

We are going to use motor imagery based BCI for stroke rehabilitation and currently I am going through some papers that discuss the EEG-EMG coherence and time lag. While the results of different...

31 October 2013 8,267 6 View

What is the best way to calculate the binary interaction parameters, for several types of compunds with CO2?(do you have Matlab code?)

#MATLAB #EOS #binary intraction #peng_robinson

01 January 1970 4,086 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Discrete Phase model (DPM) particle break-up has particle size limits during particle tracking?

Hello, I am currently working on simulating water droplet partciles in a closed room. When I use uniform particles, without "particle break-up", I can carry out the simulation without any problem....

02 March 2021 3,053 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View