01 January 1970 6 9K Report

Hello everyone

I would like to see complete derivation of K-omega and K-e turbulence model please suggest best book to understand

Thank you

More Praveen Rathod's questions See All
How to carry out survival analysis of a one time use machine which is stored and tested at regular intervals for functionality?

I want to carry out reliability study of a machine with various sub components both electrical and mechanical. The machine is a one time use (similar to a decoy or rocket) and is stored at...

30 June 2024 2,435 0 View

Is there any home portable biowaste manager ?

home based bio waste management

02 June 2024 8,590 4 View

How to develop a flat panel display glasses ?

Dear friends, I am looking to develop a new project for the applications of displays using float glass. How and what process is needed to develop such flat panel displays what are the ideas and...

09 May 2024 3,233 0 View

How do we control pin holes in the coated thinfilms by using large area magnetron sputtering techniques?

Dear ResearchGate colleagues, professors, and scientists, I'm encountering challenges with coated thin films produced using a sputtering system. Following treatment through tempering at 650...

11 February 2024 3,585 4 View

PLGA Microspheres. Alcohol or ester terminated polymers?

I have read a research paper "Development of a novel morphological paclitaxel-loaded PLGA microspheres for effective cancer therapy: in vitro and in vivo evaluations". I want to synthesize PLGA...

13 December 2023 9,857 1 View

Hello everyone, I am working on medicinal plant. How can i perform Principal components analysis?

I have done metabolite fingerprinting of plant extract using LC-MS and GC-MS.

29 November 2023 4,511 3 View

Are Geochemical Weathering and Pedochemical Weathering distinct processes?

They seems synonymous terms describing the same phenomenon.

24 October 2023 4,332 0 View

How to Deposit titanium nitride layer with x varies from 0.8 to 1.2 using sputtering coating ?

I am looking to deposit a single-layer titanium nitride layer with a sheet resistance of approximately 60 ohms and a layer of TiNx (x value should be in the range of 0.8 to 1.2). The developed...

22 October 2023 7,594 4 View

What is the name open source software for LC-MS data analysis?

Please mention name of open source software

02 October 2023 2,301 3 View

Why is the acceleration due to gravity (g) not taken into consideration when calculating the weight of soil on a one-hectare area?

Weight of soil = Area of soil * Bulk density of soil * Depth of soil. where mass=density*Volume; volume=Area* Depth. However the formula for weight in physics is mass*accelation due to gravity.

22 August 2023 9,430 5 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close