How to deposit M-O/MgO and Fe-O/MgO interface in MFe2O4?MgO thin film?

Ganesh Channagoudra @Ganesh-Channagoudra

03 February 2019 0 8K Report

Please help me regarding thin film.

I am planning to deposit MFe2O4 spinel ferrite on MgO. Is It possible to deposit M-O/MgO interface and Fe-O/Mgo interface by PLD?. If it not possible, any other method are possible?

Badges
Science topic

More Ganesh Channagoudra's questions See All

Which is the best wavelength to study aerosol optical depth(AOD) related to climate reseach,which criteria must be adopted in choosing the wavelengh?

We are doing a study on impact of aerosol on precipitation. Which satellite data and which wavelength will be the best. or can some one suggest a criteria to be adopted to choose an instrument...

12 February 2021 6,324 3 View

Let me know whether the DOI issued by the research gate will be accepted by the anna university?

As per the rules and regulation DOI is needed and paper has to be opened in online by the anna university rules let me know whether the published article in some journal and the DOI issued by...

27 November 2020 7,540 2 View

What are the alternative way to identify the stem cells present in cord blood??

commonly used practices for the identification and characterization of the kind of cell in cord blood other than Flowcytometry and reverse-transcription polymerase chain reaction (RT-PCR).

08 August 2020 6,881 3 View

What is the difference between Hex Dominant and Cut Cell Meshing methods in CFD?

Though both the methods look similar I believe there may be differences in them. What are the disadvantages of cut-cell meshing method and why is not widely used in research in comparison with...

12 July 2020 5,636 3 View

Does anyone have GS-990 DIW EIW water filtration equipment from Advantec Japan?

I tried to contact [email protected] but no response so kindly help me in this regard. We have an Advantec GS-990, it was purchased a long time ago from a Korean Collaboration. Currently,...

16 June 2020 9,890 1 View

What is the difference between anionic and cationic redox probes?

I have done Kinetics study of two different probes namely Fe(CN)63-/4- and Ru(boy)2+ on glassy carbon electrode. I kept the potential between -0.2 to 0.6 and 0.8 to 1.2 respectively. In FeCN when...

25 April 2020 3,364 10 View

Is SIMSCALE software a good to go option for visualizing and understanding academic concepts?

On what scale can SIMSCALE simulation software be helpful for students in their engineering course work comprising CFD ( Computational fluid dynamics ), thermal and structural concepts? Can...

29 March 2020 2,952 3 View

Is the Reference Intensity Ratio of Martensite(7.98) and that of Austenite (10.81), standardized against corundum, constant?

I came across the RIR value of Martensite in a paper, which is 7.98. Similarly for Austenite, which is 10.81. I want to quantify Retained Austenite in my heat treated samples. I am using Reference...

26 February 2020 9,401 2 View

Can a thermoelectric material may have negative lattice thermal conductivity?

I have calculated electronic components of thermal conductivity by wiedmanfranz law. Then the lattice thermal conductivity is derived from it. But some of those values are negative. at the end of...

26 January 2020 1,507 4 View

Anyone familiar with protein family with highly conserved C-terminal BUT very DIVERSE N- terminal, within same protein family?

Hi friends, I have been analyzing a protein family, called Fibrinogen domain related proteins, commonly called FReD or FREPs. I confronted with problem that C terminal part of this family proteins...

08 January 2020 1,320 1 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

How to call both UMAT and UEL together in Abaqus?

I have a model with bulk material (matrix) and inclusions and cohesive interface elements between both. For the bulk material, I have implemented a UMAT and for the cohesive interface elements, I...

20 February 2021 1,286 2 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

I want to remove TiO2 and SiO2 coating from surface. any one can help me?

I want to remove TiO2 and SiO2 coating from surface. I think that i should use HCl and MgCl2 and an oxidation agent such as potassium nitrate, but i dont know in which propertion should these...

14 February 2021 300 3 View

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm??

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm from the exposed surface in Abaqus... i am performing a coupled...

10 February 2021 4,656 2 View