How to decompose a backbone curve into 10 elasto plastic parallel springs in abaqus?

16 October 2019 1 1K Report

Presently I am trying to implement the SSI technique on a pile on clay soil by attaching non-linear spring decomposed from the backbone curve for my master's project. can anyone help me how to decompose a backbone curve into 10 elastoplastic parallel springs in Abaqus?

Qasim M. Shakir

Following the answers

Badges
Science topic

More Bikramjit Deb's questions See All

I want to know the BET surface area of nano-rod shaped ZnO nano-particles?

Anyone if you know the BET surface area of nano-rod shaped ZnO nano-particles than please comment. The nano rod-shaped ZnO nanoparticles are synthesized by chemical precipitation method. If...

25 May 2020 8,856 1 View

What could be the reason for a fiber shape TiO2 nanowire besed dye sensitized solar not to work?

I am trying to fabricate a fiber shape TiO2 nanowire-based dye-sensitized solar cell on Ti wire. I use a hydrothermal route to grow the TiO2 nanowires. Then I absorb the nanowires with N719 dye. I...

15 December 2019 1,407 3 View

Can I use a sonicator to clean Ti wire?

I want to use Ti wire to make fiber shape solar cell. In literature they use an ultra-sonicator to clean Ti wire. Can I use a sonicator for this purpose as I do not have an ultra sonicator...

22 August 2019 5,066 9 View

Can i uncoat my gelatin from cell culture flask?

I have coated my culture flask with more concentrated gelatin than required accidentally. I haven't seeded my cells yet. Can i uncoat them and again coat them with desired concentration?

24 April 2019 529 1 View

Can i do immunofluorescence in cover slip for my HUVEC? If so, how?

I am going to do immunofluorescence from my cultured HUVEC. Before doing IF test i need to treat my cells with my test serum sample for 6 hours. I don't have chamber slide for this. So I am in...

08 April 2019 3,948 3 View

DNA analysis in glass microfluidic channel has showed a lot of sticking problem and eventually clog the channel. Any solution to reduce DNA sticking?

I am doing DNA separation in micro-fluidic channel network made of glass. There I see DNA sticking on glass channel wall that impedes DNA movements and eventually clog the channel. After few...

19 March 2019 6,839 3 View

How to preserve and process endocervical swab for cytokin analysis by flow cytometry?

I wanna analysis cytokines level in different stages of CIN and ca cervix both in HPV DNA positive and negative cases. We collected 1000microliter cervical swab by cyto brush for detection of HPV...

12 March 2019 2,628 2 View

Can anyone please suggest me some vacuum free top electrode deposition technique for organic solar cells?

Hello, I am trying to fabricate a P3HT:PCBM based organic solar cell. I do not have thermal evaporation equipment available. Can anyone please suggest me some other vacuum free technique to...

14 February 2019 502 8 View

I am trying to fabricate a solar cell with the structure FTO/TmPyPB/PCBM/P3HT:PCBM/MoO3/Au:Pd alloy. But getting short circuit. What should I do?

Hello, I have been trying to make a 2D solar cell with the structure FTO/TmPyPB/PCBM/P3HT:PCBM/MoO3/Au:Pd. I covered a portion of FTO with an adhesive tape to deposit different layers and then...

28 January 2019 8,997 2 View

What is the probable reason for different yield of the Hydroxyapatite extracted from natural sources by different pretreatment processes?

I have extracted hydroxyapatite from natural sources using deproteinization and thermal decomposition process. it is found that for different deproteinization techniques, the yield of the...

21 January 2019 5,601 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View