How to convert vertical loads to equivalent mass of the beam element in abaqus?

Mohammadamin Vaziri @Mohammadamin-Vaziri

08 April 2019 1 7K Report

I am working on modeling a bare steel frame in abaqus. In one of the papers is written that the vertical loads were converted into the equivalent mass of the beam elements. I would thank if anyone can help me with it.

Qasim M. Shakir

following the answers

Badges
Science topic

More Mohammadamin Vaziri's questions See All

Why Hexagonal Close Packed (HCP) does not exist in Bravais Lattice ?

By referencing to simple Mathematics Calculation we should have 28 lattices In Geometry and Crystallography, but Bravais lattice includes 14 types of lattice. One of the lattices that does not...

25 October 2023 7,742 4 View

How can I determine the deviation of the angle of the camera with correction image distortion?

Hi, I research a project that needs to capture the deviation of the camera lens with distortion rate, do you have any idea how can i do that or do you know a journal to suggest to me?

08 May 2023 3,709 2 View

I have iPSC-derived cardiomyocytes on matrigel. How can I isolate iPSC-CM from matrigel?

Matrigel is at the lower and upper of cells. I want to isolate cells from the plate and matrigel and use them for WB. I used Cardiomyocyte Dissociation Kit Catalog # 05025 but It solved the matrigel.

07 October 2021 2,394 1 View

How can i have 1D plot results on an arbitrary circle around a cylinder?

I want to plot my results on an arbitrary boundary around a cylinder as in the attached picture. how can I have such an arbitrary circle dataset along the axial direction? I mean some circle...

15 June 2021 1,293 1 View

What are new trends in heat transfer and fluid mechanics?

Hello I'm currently searching for new trends related to heat transfer and fluid mechanics to select my M.Sc. thesis topic. can you please introduce me innovations and recent advancements in this area?

30 November 2020 9,525 13 View

How to mix a gas with different amounts of water vapor?

We want to measure the dew point of a gas (e.g. Argon). We want to measure it when the gas is mixed with various amounts of water vapor. We have the sealed (Argon) gas holder. How can we produce...

03 October 2020 4,742 8 View

How to Determine statistical significance of relationship between two variables that have interaction effect in smartpls 3 ?

Hi dears I have calculate the beta of Independent, Moderator and Interaction effects on a dependent variable. (beta1, beta2 and beta3) I know that final effect (Include interaction effect) of...

24 September 2020 2,208 4 View

Reducing pH without addition of anions that come with proton (H+) !?!?

I need to reduce the pH of DI water. However the anion coming with any acid is a problem for my system. Any suggestion on how I can reduce the pH without addition of anion that comes with proton?

13 July 2020 9,655 4 View

Is it possible to model the non-Newtonian Lubrication in comsol?

I want to know that is it possible to model the Bingham lubrication in Hydrodynamic module or thin fluid film module? or mabey I should use another module? #nonnewtonian lubrication #Comsol...

26 June 2020 1,932 5 View

How can i simulate the non-Newtonian lubricant for Hydrodynamic bearing in Comsol multiphysics?

In Comsol multiphysics, the bearing can simulate by Hydrodynamic bearing or thin fluid film module. But when I want to add a constitutive equation for viscosity the shear rate can not appear as a...

15 June 2020 5,144 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View