Is there any method to convert micro structure of material into nanofiber?
I would greatly appreciate any help you could give me with this.
We can use activating or etching agent to reduce the fibers diameter. While doing activation of Carbon nanofibers derived from Polyacrylonitrile we observed decrease in fiber diameter.
Hello Akshay,
You may try the electrospinning technique for fine nanofibrous structures.
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,991 0 View
How we can cite the papers from ResearchGate. I am trying to create citations for this article, Quantum Machine Learning Algorithms for Optimization Problems: Theory, Implementation, and...
08 August 2024 6,688 3 View
I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...
03 August 2024 6,069 3 View
I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...
03 August 2024 3,850 1 View
HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...
31 July 2024 5,309 7 View
I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...
31 July 2024 9,697 0 View
Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.
24 July 2024 6,290 4 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,347 2 View
Bioinformatics tools like peptide cutter
15 July 2024 6,453 1 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View
Dear All, I need to deposit Glutathione on to ready made PCL nanofiber composite, how can I physically immobilize? which way of incorporation do you recommend, physical deposition or...
18 July 2024 9,725 1 View
I have hemostatic nanofibers of hydrophilic nature. While fibrin formation from fibrinogen can be qualitatively visualized using SEM. What assays can be performed on nanofibers to quantify the...
08 July 2024 3,713 1 View
I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...
17 June 2024 9,763 0 View
Recently, I am preparing novel electrospun nanofibers for forward osmosis membrane preparation, I am facing following problems: 1. While testing water flux, there is little leakage, although the...
28 May 2024 8,510 2 View
Recently, i use Cd as a doping for ZnO Nanofiber. From some journals, Cd should increase the absorbance of ZnO. But in my case; it was not. Cd-ZnO Nanofiber has lower absorbance than the pure one....
12 May 2024 1,013 4 View
The FTO is deposited on glass substrate
01 May 2024 9,262 1 View
I have used DMSO to treat films with DMSO vapour. Can I use that same DMSO solution multiple times again?
04 April 2024 5,882 2 View
I added 4mass% also get the results of beads clumped together. Is it because the ethanol does not mix well with PET/HFIP?
29 March 2024 2,164 0 View
I have synthesized a nanoparticle which has piezo electric property and dispersed in the polymer solution to prepare nanofibres through the process of electrospinning. Is there any standard method...
18 March 2024 6,779 1 View
Hello. I am making hollow nanofibers using electrospinning technique and coaxial needle. My efforts have not been successful so far. I use PVA polymer for the shell and mineral oil for the...
22 February 2024 3,063 0 View