How can we get average velocity of of open channel by integrating over the channel height and length?

I am following one paper about the "Electrokinetic actuation of low conductivity dielectric" but did not understand the equation 35 derivations. Can anyone please help me to find Maxwell gradient...

01 February 2020 9,439 3 View

Is it possible to get 1700 v from 25 mm^2 area from tribo nanogenerator?

I am following this paper but the results are too high to get from mentioned data? Can anyone guide me about this? Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelec...

04 May 2019 2,716 1 View

I am following one paper about Tribo Electric Nano generator but getting 10000 times less results?

I have followed all the parameters and also changed them as well. But still values are 10000 times lower than the published one. I have focused on 1. Thickness of surfaces 2. Contact area 3....

04 May 2019 5,606 0 View

How can I measure or check the adhesion( interface force) between cured consecutive layers of PDMS?

Let suppose we make a PDMS lines( 50um) on glass/PET substrate and after fully curing PDMS, we cover the PDMS lines by spin coating with PDMS and again cured the whole sample. Now, how can I...

02 March 2019 3,033 4 View

Why DMA(Dynamic mechanical analysis) results of shape memory polymers are showing odd behavior?

04 May 2017 6,024 4 View

Whats can be expected applications of 2 different shape memory polymers layered one another?

Dear all, If we have 2 different shape memory polymers with different glass transition temperatures, layered one another along the thickness, then what can be expected applications? What can be...

03 April 2017 9,922 1 View

How wave length dimension play a role in curing time for 3D printing?

I am trying to cure my photo polymer using SL 3D printing technique, but material is not being cured by UV light of 405 nm. What type of parameters should be changed to cure my material?

31 December 2016 5,130 1 View

Can we fabricate four different polymers using 3D technique?

11 December 2016 8,479 0 View

Can we use our own polymer resin for SLA and Multi Jet 3D printers?

I have my own resins, how can I confirm that they are compatible for SLA and Multijet 3D printers?

10 November 2016 4,685 2 View

Which type of methods can be used to fabricate a functionally graded polymer?

Let suppose, we have two type of materials, one is in liquid shape and other one is in powder shape, is it possible to make FGM type structure?? IS possible then how can we proceed?

09 October 2016 4,353 1 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

How can I make stacked bar graph with scatter plot?

I want to make a stacked bar graph with showing each data value as dots. I tried with graph pad prism, version 6, but could not succeed. Does anyone have tried before making such graphs?

01 March 2021 9,383 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

Does anyone have a sequence for the human CD34 promoter?

I'm looking for the human CD34 promoter sequence to engineer into a vector construct. Can anyone recommend a good source for this sequence? Thanks very much, Laura

25 February 2021 8,205 1 View

Can I use TCA instead of TFA for protein analyis in RP-HPLC?

I am trying to analyze lipase using the reverse phase-HPLC C18 column. In the literature, 0.1 % TFA was and 60% ACN was used. Can I use TCA in place of TFA? If any other methods are available to...

25 February 2021 2,388 3 View

Can I use a graph from a another source in a thesis?

I have a permission from X company to use their graph from a report, but they have a reference in the bottom left corner of the graph as follows: "Source: Database Y". Is it OK to use this graph...

24 February 2021 2,269 3 View

I have need of XRD graph analysis software for phase identification. Can you please provide links for software tools which can be downloaded?

i am trying to download x'pert high score software, but can't download it. please do suggest software for phase analysis

24 February 2021 5,687 4 View