How to configure ABAQUS solver for ANSYS Mechanical?

More Rashiga Walallawita's questions See All

How to do function multiplication in APDL?

I need to define a simple equation in APDL with multiplication in it. The function goes as, w = REV * 2* PI/60 I simply want to convert the input RPM value to rads-1. But when I enter the equation...

10 November 2019 4,320 3 View

How to add "remote displacement" type boundary condition in APDL?

Hi all, I want to know how to add DOF for a set of nodes relative to a remote location in APDL? A similar function is available in Ansys mechanical workbench called 'remote displacement" or...

08 September 2019 9,840 2 View

How to convert bolt pretension torque to pretension adjustment length??

Hi, How to convert bolt pretension force in to "pretension adjustment length"? Is there any equation for the conversion? Or do I have to conduct a separate simulation to find the bolt length...

06 July 2019 9,703 7 View

How to select surrogate model based on multiple error metrics?

HI, I need to select a single surrogate model to model the response of four different objective functions. To do that I have errors of each surrogate model from three different error metrics. My...

04 May 2019 9,081 5 View

ANSYS WB : How to obtain volume of a single object in an assembly(for parametric study)?

Hi, I'm doing a stress analysis of an assembly. I need to obtain the volume of an object as an output parameter for a parametric study. How can I do that? I think I can use a apdl command to...

02 March 2019 1,321 1 View

Extracting "user defined results"?

Hi, I need to calculate factor of safety for a brittle material using "elemental" max. principal stress. Since the default factor of safety is based on "nodal" stress. I'm planning to use "user...

01 February 2019 6,458 1 View

Are there any research paper on removing stress singularities using St. Venant's principle?

Hi all, In FEA when dealing with stress singularities, most of the time people say to avoid the stress singularities using the St. Venant's Principle. But to back it up this method I could not...

10 November 2018 4,108 8 View

How to setup ANSYS distributed fro Mechanical workbench?

I need to use computing power of two computers for simulation. How do I setup this for ansys workbench mechanical? Thanks.

09 October 2018 4,845 0 View

How to select mean stress correction method for fatigue simulation/analysis?

There are several types of mean stress correction methods in fatigue analysis such as Goodman, Gerber, etc, So for a fatigue analysis what is the basis of selecting a mean stress correction...

07 August 2018 9,580 12 View

How to overcome stress singularities due to interference fit?

HI all, I'm trying to simulate the effect of rotational inertia for a shaft which is rotating 100 krpm along its axis. The shaft consists of three components (please see the below attachment...

06 July 2018 7,840 9 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Edmundas Reiciunas

Hi, Not sure if this is what you are searching for but anyway.

You can Iinsert Commands as you would Insert force or anything else in your problem. And in that Comands (ADPL) there is an option Definition->Target->Mechanical (ADPL) [as default], but you can change it to ABAQUS among other options.

David Sziroczak

I can help you with how to run Ansys files in Abaqus, but I don't know how to set them up in Ansys workbench.

If you use Abaqus /CAE, you can import a nastran input file. Or use the translator from the command line: "abaqus fromansys job=... the ansys input file name..."

Obviously conversion is never guaranteed to be 100%, so you might have to fix a thing or 2, but after that you have an Abaqus .inp file that you can execute.

Hope this helps,

Best regards,

David

Bilal Sarfraz

Enable Beta options in your Ansys Workbench