ANSYS WB : How to obtain volume of a single object in an assembly(for parametric study)?

Rashiga Walallawita @Rashiga_Walallawita2

03 March 2019 1 1K Report

Hi,

I'm doing a stress analysis of an assembly. I need to obtain the volume of an object as an output parameter for a parametric study. How can I do that?

I think I can use a apdl command to get this but I still cannot understand how to implement it.

Thank you.

Best Regards,

Rashiga

Oleg Gnedkov

Do you want to get the volume of the object in m^3?

If yes, you can do: model->Geometry->your solid body->properties(In details)

Badges
Science topic

More Rashiga Walallawita's questions See All

How to do function multiplication in APDL?

I need to define a simple equation in APDL with multiplication in it. The function goes as, w = REV * 2* PI/60 I simply want to convert the input RPM value to rads-1. But when I enter the equation...

10 November 2019 4,320 3 View

How to add "remote displacement" type boundary condition in APDL?

Hi all, I want to know how to add DOF for a set of nodes relative to a remote location in APDL? A similar function is available in Ansys mechanical workbench called 'remote displacement" or...

08 September 2019 9,840 2 View

How to convert bolt pretension torque to pretension adjustment length??

Hi, How to convert bolt pretension force in to "pretension adjustment length"? Is there any equation for the conversion? Or do I have to conduct a separate simulation to find the bolt length...

06 July 2019 9,703 7 View

How to select surrogate model based on multiple error metrics?

HI, I need to select a single surrogate model to model the response of four different objective functions. To do that I have errors of each surrogate model from three different error metrics. My...

04 May 2019 9,081 5 View

Extracting "user defined results"?

Hi, I need to calculate factor of safety for a brittle material using "elemental" max. principal stress. Since the default factor of safety is based on "nodal" stress. I'm planning to use "user...

01 February 2019 6,458 1 View

Are there any research paper on removing stress singularities using St. Venant's principle?

Hi all, In FEA when dealing with stress singularities, most of the time people say to avoid the stress singularities using the St. Venant's Principle. But to back it up this method I could not...

10 November 2018 4,108 8 View

How to setup ANSYS distributed fro Mechanical workbench?

I need to use computing power of two computers for simulation. How do I setup this for ansys workbench mechanical? Thanks.

09 October 2018 4,845 0 View

How to select mean stress correction method for fatigue simulation/analysis?

There are several types of mean stress correction methods in fatigue analysis such as Goodman, Gerber, etc, So for a fatigue analysis what is the basis of selecting a mean stress correction...

07 August 2018 9,580 12 View

How to overcome stress singularities due to interference fit?

HI all, I'm trying to simulate the effect of rotational inertia for a shaft which is rotating 100 krpm along its axis. The shaft consists of three components (please see the below attachment...

06 July 2018 7,840 9 View

How can stress concentration occur on flat contact surfaces?

Hi all, I've being trying to simulate effect of bolt pretension using ANSYS mechanical. The bolt load is 12000 N. I'm using axi-symmetric simulation. The issue is stress concentration is high on...

04 May 2018 8,501 1 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Anyone plz suggest relevant topic for research in image processing+Deep learning.?

I have selected brain tumor images ...but now found that already lots of research done n this topic.

03 March 2021 5,774 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Chlorinated organic formation in odor control scrubbers using hypochlorite?

I'm involved in a study of odor control technologies for municipal wastewater treatment plant. One of the control options involves a chemical 2-stage (acid/alkaline) packed bed scrubber. The...

03 March 2021 3,661 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View