How to setup ANSYS distributed fro Mechanical workbench?

Rashiga Walallawita @Rashiga_Walallawita2

10 October 2018 0 5K Report

I need to use computing power of two computers for simulation. How do I setup this for ansys workbench mechanical?

Thanks.

Badges
Science topic

More Rashiga Walallawita's questions See All

How to do function multiplication in APDL?

I need to define a simple equation in APDL with multiplication in it. The function goes as, w = REV * 2* PI/60 I simply want to convert the input RPM value to rads-1. But when I enter the equation...

10 November 2019 4,555 3 View

How to add "remote displacement" type boundary condition in APDL?

Hi all, I want to know how to add DOF for a set of nodes relative to a remote location in APDL? A similar function is available in Ansys mechanical workbench called 'remote displacement" or...

08 September 2019 10,201 2 View

How to convert bolt pretension torque to pretension adjustment length??

Hi, How to convert bolt pretension force in to "pretension adjustment length"? Is there any equation for the conversion? Or do I have to conduct a separate simulation to find the bolt length...

06 July 2019 9,945 7 View

How to select surrogate model based on multiple error metrics?

HI, I need to select a single surrogate model to model the response of four different objective functions. To do that I have errors of each surrogate model from three different error metrics. My...

04 May 2019 9,237 5 View

ANSYS WB : How to obtain volume of a single object in an assembly(for parametric study)?

Hi, I'm doing a stress analysis of an assembly. I need to obtain the volume of an object as an output parameter for a parametric study. How can I do that? I think I can use a apdl command to...

02 March 2019 1,440 1 View

Extracting "user defined results"?

Hi, I need to calculate factor of safety for a brittle material using "elemental" max. principal stress. Since the default factor of safety is based on "nodal" stress. I'm planning to use "user...

01 February 2019 6,591 1 View

Are there any research paper on removing stress singularities using St. Venant's principle?

Hi all, In FEA when dealing with stress singularities, most of the time people say to avoid the stress singularities using the St. Venant's Principle. But to back it up this method I could not...

10 November 2018 4,218 8 View

How to select mean stress correction method for fatigue simulation/analysis?

There are several types of mean stress correction methods in fatigue analysis such as Goodman, Gerber, etc, So for a fatigue analysis what is the basis of selecting a mean stress correction...

07 August 2018 9,728 12 View

How to overcome stress singularities due to interference fit?

HI all, I'm trying to simulate the effect of rotational inertia for a shaft which is rotating 100 krpm along its axis. The shaft consists of three components (please see the below attachment...

06 July 2018 8,004 9 View

How can stress concentration occur on flat contact surfaces?

Hi all, I've being trying to simulate effect of bolt pretension using ANSYS mechanical. The bolt load is 12000 N. I'm using axi-symmetric simulation. The issue is stress concentration is high on...

04 May 2018 8,690 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Which test should be used to study association among demographic profile and awarness level?

i have to study the awareness and adoption level of cloud computing in a district of India. i also want to use association among demographic variables like gender, age, education, income etc and...

02 August 2024 2,420 3 View

Difficulty with permittivitt and Magnetic Permeability Calculations?

Difficulty with permittivitt and Magnetic Permeability Calculations Hello everyone, I have all the parameters related to the calculations of the permittivitty and magnetic permeability...

30 July 2024 5,206 1 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

All math can be explained by iterator of code?

all math can be traversed by code? all math can be translate to code?

26 July 2024 9,530 0 View

What is human-computer interaction (HCI)?

22 July 2024 10,056 2 View

Which are the Scopus Indexed Journals in Computer Science with short review time?

Hello, I am looking out for Scopus Indexed Journals in Computer Science with short review time and short time to publish after acceptance (with / without APC). Please mention the journals that you...

19 July 2024 4,250 2 View