How to compute the phase angle of more than two images (Sequences of images) using complex morlet in wavelet transform?

More Shrestha Ranjit's questions See All

What could be possible reasons of using copper sheets to simulate delamination in composite materials?

The attache Fig. shows a square-shaped test sample with 16-layer glass epoxy with dimensions of 300 × 300 mm and a thickness of 1.4 mm. The thickness of each layer was approximately 0.0875 mm. The...

31 December 2017 6,512 1 View

How to model the temperture rise due to propogation of ultrasonic waves in a crack specimen?

Hello Experts, Any idea about how to model the tempearure rise due to the propogation of ultrasonic waves in the crack specimen? The frequency used for excitation of structures is 40 kHz. I have...

09 October 2016 2,915 8 View

What could be the best methods to improve the cooling efficiency of an active array antenna?

Hello Researchers, Could anybody let me know the best methods to improve the cooling efficiency of an active array antenna?

07 August 2016 623 2 View

What could be the tentative velocity of exhaust gaseous and coolant water while entering EGR system?

Hello Everyone, I am trying to simulate the shell and tube type Exhaust Gas Re-circulation (EGR) system using ANSYS fluent. I have the temperature data of exhaust gaseous and coolant while...

05 June 2016 6,681 1 View

How can we convert the hollow area of pipe (model in Catia) to fluid domain in Ansys fluent?

I had model a EGR system in Catia. In order to import to Ansys Fluent, i saved the model in .stp format. I wonder that the pipe geometry can only selected as a wall only. And there is no geometry...

05 June 2016 5,868 4 View

How can we save the double type image to Integer (16 bit) format or float format by using MATLAB?

Hello Everyone, A very good afternoon, I am using 'Thermofit Pro" software for the post processing of images after completing the pre-image processing in MATLAB. Since the input images in...

02 March 2016 6,104 7 View

How to check the plagiarism for research articles?

Can anybody suggest me, how to check the plagiarism for research articles? Which software's are the most effective and freely available? And how much plagiarism is supposed to allow on the...

11 December 2015 2,941 3 View

Determination of Scale (a) and Shift (b) for Complex Morlet Wavelet Analysis.

Hello everyone, I am trying to compute the phase angle data using continuous wavelet transform from the raw thermal sequence recorded with Infrared Camera. Is there any way to select Scale (a)...

01 January 1970 7,721 2 View

What could be the best substrate material when Ceramic (Silicon Carbide) is used as a Top Coat?

Hello Researchers, Could somebody help me for the selection of the best substrate material when Ceramic (Silicon Carbide) is used as a Top Coat? With regards,

01 January 1970 669 6 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Dirty and clean?

Hi everyone I need a file with a dirty and clean potato image

04 August 2024 7,199 4 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

How to do wavelet transform of EXAFS data?

I want to do wavelet transform of some compounds for their comparative study? Kindly help me in this regard and provide with proper procedure.

31 July 2024 4,170 0 View

Difficulty with permittivitt and Magnetic Permeability Calculations?

Difficulty with permittivitt and Magnetic Permeability Calculations Hello everyone, I have all the parameters related to the calculations of the permittivitty and magnetic permeability...

30 July 2024 5,206 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

How can I calculate formation energy using VASP-Ab-initio?

I would like to calculate the formation energy of P2-Na0.67Fe0.5Mn0.5O2 based on DFT, what should I do step by step. Any help would be appreciated. Thanks.

29 July 2024 8,248 2 View

IHC profiler in image j software. has anyone used it to quantify nuclear DAB positivity?

Dear researchers. I tried using the IHC PROFILER in image j to quantify nuclear DAB staining. I followed the instructions in the original article by "Varghese F, Bukhari AB, Malhotra R, De A...

29 July 2024 2,229 0 View

While using the IHC PROFILER plugin in image j software, to quantify the epithelial cytoplasmic DAB staining do you crop remove the stromal tissue?

My question pertaining to the DAB staining in cytoplasm of human oral squamous cell carcinoma tissue. When quantifying the epithelial cancer cells do we have to crop remove the stromal tissue?...

29 July 2024 2,682 6 View

Vikas Ramachandra

For the wavelet coefficients, at each scale/orientation/subband, you can compute the amplitude and phase.

what is the aim of this?

Shrestha Ranjit

Hello Vikas,

I am trying to compute the phase angle information of the recorded images using Morlet Wavelet analysis in MATLAB. As an example, I have 250 sequential images of size 640x480 pixel. For this case, what are scale and shift and how can we determine the appropriate scale and shift?

Can you please share your idea in detail?