09 September 2018 1 9K Report
  • How to compute shear correction factor experimentally and numerically ?
  • The shear correction factor needed for thin walled structures using FSDT is 5/6.

    • More Manish Kumar Dubey's questions See All
    Which shell theory is applicable for higher L/R ratio (>100) & lower R/h ratio (<10) ?

    There are shell theories like Love's, Donnell-Vlasov, Sander's,etc genrally used. Which theory is applicable here based on the limiting ratio mentioned above ?

    10 November 2018 5,634 7 View

    Display complete axes of 3D plot in Matlab ?

    I couldn't see any options to show complete axes of 3D plot in MATLAB software ? There is option to tick Box. But it doesn't covers top axes in

    08 September 2018 10,015 3 View

    Can we model Axi-symmetric and plane stress analysis together in ANSYS APDL ?

    In ANSYS APDL, the element type is normally available either for Axisymmetric or Plane stress behavior.

    08 September 2018 5,901 14 View

    Is there any faster and accurate method to solve inverse of a large size matrix ?

    First a large size matrix requires sufficient memory to inverse the matrix. Secondly, there are several mathematical techniques are available to solve the inverse of a matrix. But in handling a...

    08 September 2018 6,500 25 View

    Which is the most effective continuation methods in solving Nonlinear Dynamic problem?

    On what parameters the selection of continuation method depends ?

    08 September 2018 8,024 7 View

    What are the different forms of electro-elastic coupling available for piezoelectric material ?

    One such type of electro-elastic coupling is Constitutive relations : {stress} = [C] * {strain} + [d] *{E}; {D} = [d]*{strain} + [permitivitty]* {E}

    08 September 2018 519 17 View

    How to assign loss and storage modulus of viscoelastic material in ANSYS or ABAQUS ?

    Is there any element type available to model viscoelastic material ? There is only option available to model viscoelastic material in ANSYS is using prony series but that couldn't help me.

    08 September 2018 567 6 View

    In active vibration control- Is there any effective control strategy?

    There are control strategies like LQR, Positionfeedback control, Negative velocity feedback control, etc. Which one will provide better active control of vibration ?

    08 September 2018 7,398 4 View

    Is it possible to do homogenization analytically for irregular shaped RVE ?

    Normally, representative volume element (RVE) of the composite is independent of geometry. There are several homogenization methods available that defines regular shaped like rectangular,...

    08 September 2018 437 4 View

    How to plot a stress/strain distribution of any section or plane in ANSYS ?

    Is there any option to plot a stress or strain distribution of a section or plane of a given configuration ?

    08 September 2018 7,807 2 View

    Similar questions and discussions
    MD MOE RMSD

    How to calculate the RMSD values for a MD simulation using MOE?

    07 August 2021 0 0 View

    MD MOE RMSD

    How to calculate the RMSD values for a MD simulation using MOE?

    07 August 2021 0 0 View

    fatal error

    When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

    16 June 2021 0 0 View

    fatal error

    When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

    16 June 2021 0 0 View

    fatal error

    When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

    16 June 2021 0 0 View

    fatal error

    When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

    16 June 2021 0 0 View

    flexibility of polymers chain

    effect of double bond on the flexibility of polymers

    07 April 2021 0 0 View

    Formulation of polymer color flakes

    I am writing to request some information for making polymer color flakes. I would appreciate the help.

    17 March 2021 0 0 View

    How to compare two groups with only two measurements?

    Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

    03 March 2021 8,796 3 View

    Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

    I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

    03 March 2021 3,568 1 View

    Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close