What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

How can we theoretically calculate Elemental analysis(percentage) of atoms in covalent organic framework?

For example in one research article the Elemental analysis values of COF-TpPa-1 ( Triformylphloroglucinol (Tp) (63 mg, 0.3 mmol), Paraphenylenediamine (Pa-1) (48 mg, 0.45 mmol) are as follows...

24 February 2021 1,265 6 View

Is there any teachers based in UK who would like to take part in my study?

24 February 2021 4,833 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

SSR primers are species specific or we can use it for any plant species ?

Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...

20 February 2021 315 4 View

In CDA analysis we have three stages, viz., description , interpretation, and reproduction. Why have all CDA studies neglected the third stage?

In CDA analysis we have three stages, viz., description , interpretation, and reproduction. Why have all CDA studies neglected the third stage?

18 February 2021 6,483 3 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

Can I use a categorical covariate in a Generalized Linear Model in SPSS v.26?

Hello everyone, hope you are well. I am planning to use a Generalized Linear Model in SPSS. I would like to add gender to the model as a covariate, however from what I have read, only continuous...

14 February 2021 8,937 4 View

A Hardware Architecture of Lee Algorithm for Finding the Shortest Path in a Maze by using Verilog code?

how to write lee algorithm in Verilog code, if could someone help.

20 December 2020 8,565 1 View

How to calculate power of Verilog A based Stanford CNTFET model in Cadence Virtuoso?

I have implemented several basic circuits using VS- CNTFET Stanford model in Cadence Virtuoso. All the circuits are showing proper transient response, but power plot is coming out as zero( in...

19 October 2020 2,954 4 View

How to add Stanford University CNTFET Model in OrCAD PSpice?

The HSPICE and Verilog versions are available here https://nano.stanford.edu/stanford-cnfet-model. Is it possible to add CNTFET model in OrCAD Pspice and if yes, what are the steps regarding this.

12 October 2020 916 2 View

Can a wire/tri be assigned z and 1/0 at the same time? What value will it take then? Could you provide any references?

Suppose A is a 'tri'. A is being connected to the output of a module which is instantiated twice,in both the instances. In one instance the value of A will be 1'bz and in the other it will be...

27 March 2020 1,294 2 View

How to simulate the veriloga based Stanford CNTFET model in Cadence?

I am trying to simulate following the instructions in the pdf attached. But I keep getting the following error: "Missing or corrupt .oa file in cellview 'cnt/nCNT/spectre cmos_sch cmos.sch...

11 March 2020 9,590 4 View

How to store data in FPGA and display the same to a computer monitor with the help of FPGA VGA or any other port?

I have 100 samples of data (sampled at 170 Hz) each having 16-bit wide, first of all I want to store the data in FPGA basys 3 board and secondly how it can be displayed with the help of FPGA VGA...

07 August 2019 8,229 4 View

Writing testbench for filter using ecg data?

i have to write a testbench for iir filter using verilog. These testbench will contain a .txt file of ECG data. I am not getting any idea....can anyone help me how to start? Thanks

01 February 2019 1,378 8 View

How to call verilog a file (.va file) in ICCAP for parameter extraction in compact model?

Actually I have used the following format. But it does not work. #load "veriloga", "path of the veriloga file" During simulation it is showing "unknown model type". Here I am using model type as...

31 December 2018 9,348 0 View

Integral Operator in SystemVerilog - RNM?

I am working on a mixed-signal IC design using SystemVerilog - Real Number Modeling. I have to convert an expression argument into its integrated form. There is a circular integrator operator in...

08 September 2018 2,112 2 View

Conditional execution in verilog?

Hi, I am trying to implement a particular code in verilog whose pseudo code is given below. I have problem with the while loop(LINE 7 & 11). I get this error when the while loop is used;...

07 August 2018 8,568 1 View