How to carrying out strain modal analysis using AnsysWorkbench?

More Rachid Azzi's questions See All

How to resume a Gate (geant4) simulation after a crash or power failure?

Very long simulations may be subject to computer failure for many reasons. Is there a command in Gate to save (or dump) the state of a simulation and be able to resume it later?

04 October 2020 8,133 2 View

How to apply a different material on a group elements of global model?

how to apply a different material on a group elements of global model? i have a wind turbine blade model (complex model) . I want to model a defect on the blade by reduction of young modulus of a...

17 August 2020 1,377 3 View

What do you think about the expulsion of 21 teachers in Jordan university ?

Hello What do you think about the expulsion of 21 teachers in Jordan university because they did not publish any research in the last five years ? Is this an efficacy solution , can we apply it...

22 July 2020 914 34 View

How to draw light lines on dispersion diagram extracted from CST- eigenmode solver?

Hello, I have a non symmetric unit cell with a period over y axis of 48mm. I know that f= c. teta / 2*pi*p having teta in radians. However, I am getting a very weird light lines.

25 May 2020 5,889 3 View

What is the best method for non-linear resolution of the solar/PV cells characteristic ?

Evolutionary Algorithms, namely Genetic Algorithm (GA), Particle Swarms Optimization (PSO) and Differential Evolution (DE) are used to solve optimization problems. As in photovoltaics (PV), the...

05 May 2020 8,708 8 View

How to find the displacement of each of the model nodes as well as its position on the model using AnsysWorkbench, after a modal analysis?

In several studies of the analysis of the defect effect on the dynamic characteristics of the structure, the defect is modeled by reduction of the modulus of young. I want to perform this method...

20 April 2020 4,644 3 View

What is the relationship between Glass Transion Temperature (Tg) and testing rate?

In other terms the influencing of testing rate on Tg. Excuse me for my beginning english

14 January 2020 706 3 View

Can anyone help me in classification of EEG signal?

Can anyone help me in classification of EMG signal? I had EEG signal and want to classify into four different action by using matlab classification learner app. I had xdata with time and ydata...

16 September 2019 3,698 2 View

A recurrent question about interaction value in linear mixed model. How to get it with a t value?

I apologize for asking again the same question, but il really don't have a satisfactory response. In different article, I find more and more (focused on eye movement in reading) that interaction...

05 June 2019 3,223 8 View

Non linear optical parameters of Calcite and Quartz crystals?

I am looking for the Non linear optical parameters of Calcite and Quartz crystals in the telecom window (1.2 - 1.7 micrometer).

28 January 2019 2,615 2 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View