How to Calculate the thickness of thin films by XRD (Xray reflectometery) ??

More Syed Ali Hassan's questions See All

A 20 fs FWHM transform-limited Gaussian pulse, with carrier wavelength of 1050 nm, goes through 1 meter of fused silica.??

A 20 fs FWHM transform-limited Gaussian pulse, with carrier wavelength of 1050 nm, goes through 1 meter of fused silica. What is the FWHM pulse duration at the end?

10 November 2018 6,464 2 View

Is there any other ways to estimate the crystalite size of because Scherrer's equation to determine the crystallites size is not recommended.??

Is there any other ways to estimate the crystalite size because Scherrer's equation to determine the crystallites size is not recommended. I am looking answer for Single crystalline oriented...

31 December 2017 5,277 3 View

Why MgO (110) and (111) are not effected by heat treatment??

I Did some heat treatment with MgO substrates with (100), (110), (111). I observe significant changes on MgO (100) surface morphology (atomic steps), but other two substrate remain unchanged....

02 March 2017 4,809 3 View

How to calculate the interfacial energy of dielectric substrates??

So my question is related Interfacial enegry calculation.If i have MgO substrate and we deposited Pt thin films on it.. I need to know the MgO surface energy before deposition? is there any...

02 March 2017 5,577 3 View

Why Pt can not be deposited on Si substrate for the application of electrocatalytic applications?

Mostly ceramic substrates (MgO, STO, LaAlO3 etc..) are used to deposit transition Metals (Pt,Ag,Au,Cu) for the electrochemical applications. Why Silicon Substrate can not be used for such...

02 March 2017 7,716 7 View

Why XRD patterns are indicating that Pt (110) and (111) are formed on MgO substrate but AFM shows some inappropriate structures?

Pt films deposited on MgO (110) and (111) were grown , as a result no elongated features and traces on MgO (110) and (111) were observed . Instead it was seen that a disordered 3 dimensional...

31 December 2016 2,214 4 View

How to measure the critical angle in XRR(X-ray reflectometery ) result?

I did XRR analysis to calculate the thickness of thin film. can any body explain what is critical angle in XRR measured graph. and how to measure this critical angle???

11 December 2016 4,849 3 View

Lattice parameter changes by changing the Concentration during alloy formation, does it effect the Morphology of thin films??

For example in NiFe thin films, if the concentration of Ni is change by wt% 33,40,50,60 in Fe .. what are the possible factors that changes the surface morphology (topography) of the thin film for...

10 November 2016 3,018 7 View

By Increasing the substrate temperature (Rt to 600c) we observe increase in the Peak Area graph from XRD 2theta analysis, What does that mean?

The intensity of the Graph is increasing with respect to temperature. If i plot a graph with respect to Area of that peak and temperature I observe also increase in area. what does that mean? If...

10 November 2016 7,599 11 View

How can we estimate about the deposition rate of material of PLD deposited thin films??

If I know the thickness of the film (15nm). How I can justify about the deposition rate of the material ? Which formula or which method?? Please help

10 November 2016 1,976 5 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Is there a good freeware software for photodocumentation of TLC?

I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?

31 July 2024 8,415 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Does anybody know why my chitosan/pva/gelatin hydrogel dissolve in PBS?

My final research is about making chitosan/pva hydrogel for wound healing using gelatin as crosslinker. Last month, i made the thin film hydrogel and it turn well. It was okay. Last week, i make...

28 July 2024 2,794 6 View

Does post-translational protein modification cause devisions on observed pI verses calculated pI?

In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....

24 July 2024 8,076 3 View

How can I better use imageJ to get good result on calculating surface area of a film accurately?

I have images of film formed on the bottom of a 50mL beaker, and I have been trying to figure out the surface area. I could easily use features on imageJ to do that, but I want to know which area...

23 July 2024 4,461 1 View

Shen-Ming Chen

You might calculate the thickness of thin films by X-ray reflectivity measurement. Reflectivity of a film on substract. ex. copper on Si substract.

A. El-Denglawey

Dear colleague Dr. Ali, Have a nice time and good day.

please follow the next website it contains the answer for your question

yours. A. Eldenglawey

https://www.researchgate.net/post/Please_any_suggestion_how_to_estimate_the_thickness_of_thin_films_Co_Cu_Multilayers_using_Low_angle-XRD

Ahmed Saeed Hassanien

Dear Dr. Ali Hassan Kazmi

My greeting

The following attached paper may be useful for your calculations

Regards