How to calculate Skin friction Drag using Ansys CFX or StarCCM ?

05 May 2017 0 3K Report

i need to calculate Skin friction drag computationally...Any Help

Badges
Science topic

More Manigandan Sekar's questions See All

In fluent heat flux analysis results are not converging ?

I had solved the heat flux analysis of the multi-domain problem in fluent. Even after the 20000 iterations also the solution is not converging. As the iterations increase the results are diverging...

10 November 2019 3,972 3 View

How to draft a review paper effectively in short span of time for high impact journals?

Writing a review paper required a lot of effort. Any tactics is there to complete it in short span of time. Especially for Elsevier or reputed journals with high Impact factor.

06 July 2019 2,293 3 View

Do addition of nanopartilces in soil increases the Plant yield ?

Can any one explain me that addition of nanoparticles enhances the growth of plant and produces more yield. If so, can anyone list me the nanoparticles i can use Plant is Tomato and Aubergines

05 June 2019 268 4 View

No title

I came across few having 3 PhD in different fields. Am very confused about this ? Thanks in advance

02 March 2019 7,556 2 View

Is addition and removal of Co-author during submission of revised article is acceptable @Elsevier ?

I like to know the removal, addition and shuffling of co-authors is against moral and ethics in Elsevier Journals. Is it necessary to contact a editor to make such changes

01 February 2019 1,137 15 View

Differences between research papers and technical note of journal?

Can i write an technical note below 1000 words. If not what is the idle limit for them. Is there any mandatory rules

31 December 2018 9,217 1 View

Best way to access recent Engineering Books in online ?

I need to access the book : Energy Efficiency in Air Transportation Published by elsevier. I tried many options but no use. Since i can't afford to buy this, is there any way to access the ebooks

31 December 2018 4,163 4 View

How to solve Blast in FEA ?

What are the boundary conditions are required for blast loading. Share the tutorials if possible.

31 December 2018 1,249 0 View

What is the difference between review track and non review track in Elsevier conference ?

In Elsevier conference there are two options for paper submission Review track and non review track. What is the meaning for that. Will they publish both articles in supporting journal

07 August 2018 3,866 0 View

How to approach Faculty Exchange Program to the foreign Universities ?

Hi Am looking for an Faculty exchange programme vacancy in foreign universities to improve my career in technical fashion. I don't know how to start them. Can anyone guide me

07 August 2018 8,713 1 View

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

QPCR reaction efficiency with odd results what does this indicate?

I am working on a CFX 96 machine to determine reaction efficiency of my gene of interest. After performing a serial dilution of my cDNA template, I was able to find great reaction efficiencies for...

23 February 2021 809 3 View

How to calculate time-averaged fields from Ansys CFX solver?

I would appreciate any comments on the following problem. I need to calculate mean fields (e.g. pressure, velocity and vorticity), for which I activate Trn Stats tab in CFX-Pre. However, what I...

21 February 2021 8,548 7 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View

Is it possible to add a source term to the momentum equation in ANSYS CFX?

I want to add a source term as a body force to the momentum equation in Ansys CFX for modeling the VGs and I don't know how do it !!

21 February 2021 2,971 4 View

How do you integrate the 'friction' variable Xi in the Nose - Hoover Thermostat in order to apply it to a molecular dynamics simulation?

Everything tells you the derivative of Xi, but not how integrate the value to implement it into a simulation. How do you do this?

21 February 2021 6,481 1 View