How to calculate effective bond area ?

More Prabin Pathak's questions See All

Why the journal "the lancet" is only indexed in scopus?

I went through "The Lancet" journal website and saw the immense impact factor of 60.392. Then to my surprise I found that the journal is only indexed in scopus. Such Imapct factor journal is...

21 December 2020 152 3 View

Which factor controls Peak intensity in Rietveld refinement?

I am refining structural parameters of my sample. after inserting all parameters in sequence, When I take first Run in refinement, the intensities of all peaks diminishes to zero of calculated...

07 October 2020 8,598 1 View

What would be the effect of size of the nanoparticles on the birefringence of nematic liquid crystalline materials?

Usually, birefringence of nematic liquid crystals (NLCs) can be tuned by doping of nanoparticles into it. But what will happen if we dope the same nanoparticle of different sizes? Will...

20 September 2020 3,693 3 View

Which is better for thin film growth, electron beam evaporation or sputtering?

which is better for thin film growth, electron beam evaporation or sputtering? which results in better film quality?

24 July 2020 6,275 4 View

What minimum operating voltage for CMOS technology and magnetic field required for spintronics technology?

Generally, we always try to give low input to operate a device. What are the minimum values of voltage for CMOS technology and magnetic field for spintronics technology?

24 July 2020 5,610 2 View

Where do I find consumer mobile datasets that include his or her social media activity and his smart home dataset?

I am looking for a data set to find out the loyal consumers.

26 June 2020 2,973 1 View

Which technology should we need to apply to get the present condition of soil and suggest us some crops from a remote place?

At present we are updating our work. So I need your suggestions. https://www.researchgate.net/publication/335800982_IoT_based_Smart_System_to_Support_Agricultural_Parameters_A_Case_Study

20 June 2020 3,748 11 View

How to plot data in 10X10 matrix in which all the diagonal elements are 0 and the matrix is symmetric about the diagonal?

I have a data of comparison of 10 proteins with each other under two parameters i.e 100 entries in the shells of two 10X10 matrix in excell sheet. I want to see whether both of these data sets...

02 March 2020 1,593 5 View

What are the effects of using powerful magnets around AC current?

I am trying to connect two sockets( sockets being flat surfaces on both sides) using powerful (small sized ~8mm diameter) neodymium magnets with 3 or 4 on each side of the socket so that the pull...

03 January 2020 8,835 3 View

How to implement AntHocNet or AntNet in NS2.35 for wireless sensor network?

I want to implement the Ant colony algorithm for a wireless sensor network using ns2. But I'm not sure about the process of implementing that. Please provide information about how to implement ACO...

29 December 2019 6,765 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View