I want to go through the same method FEA softwares are using. Apply meshing and FEA on CAD geometry? How can I do it? Which book to follow?
https://www.researchgate.net/publication/341464814_Application_of_Reverse_Engineering_and_Rapid_Prototyping_for_Reconstruction_of_Human_Mandible
you may use Ansys ICEM ,
Dear Hao,
I want to make my own package like commercial softwares.
Why direct inversion of mutivariate regression equation is not preferred and instead optimization techniques are used?
15 July 2024 8,642 3 View
I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?
01 July 2024 3,749 0 View
I am trying to imitate orthogonal cutting in 2D in abaqus. Can anyone suggest me any reliable research paper?
30 June 2024 7,306 0 View
Maximum likelihood estimation is used to estimate population mean and variance. However, we can do it with sample variance too and sample variance is unbiased also. Then why we prefer maximum...
25 June 2024 3,920 3 View
I am doing 2D orthogonal cutting simulation in ABAQUS for aluminum. Reducing mesh size up to 0.08 mm reduces the error to 3% but further reduction leads to increase in error from 3 to 39%. Why I...
23 June 2024 9,080 0 View
I am doing orthogonal machining of aluminum in 2D. However, when partitioning for depth of cut with a sketch on face strategy with a parting line, it says that face could not be partitioned. How...
18 June 2024 8,000 0 View
I am trying to simulate orthogonal cutting. My analysis time is stuck at 0.03125 seconds. I killed it and started again. It is again stuck.
27 May 2024 4,917 1 View
I am trying to predict cutting forces in orthogonal cutting using Oxley's model using power law in flow stresses. However, I can't get out of the loop where temperature is just changing...
02 December 2023 4,964 0 View
I am currently working on research and review papers and need suggestions regarding creating attractive figures.
25 February 2022 9,068 5 View
I have started learning FEM from scratch. I want to apply it to do numerical simulation of solidification in ANSYS? Where and how to start learning ANSYS?
14 February 2022 8,484 6 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,099 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,136 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,769 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,428 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,936 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,105 4 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,987 3 View