A standard paper for 2D orthogonal cutting?

Vishesh Dharaiya @Vishesh-Dharaiya

01 July 2024 0 7K Report

I am trying to imitate orthogonal cutting in 2D in abaqus. Can anyone suggest me any reliable research paper?

Badges
Science topic

More Vishesh Dharaiya's questions See All

What are the problems we face when we directly inverse a multivariate regression equation?

Why direct inversion of mutivariate regression equation is not preferred and instead optimization techniques are used?

15 July 2024 8,642 3 View

How to decide mass scaling in ABAQUS?

I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?

01 July 2024 3,749 0 View

Why maximum likelihood approach over sample variance?

Maximum likelihood estimation is used to estimate population mean and variance. However, we can do it with sample variance too and sample variance is unbiased also. Then why we prefer maximum...

25 June 2024 3,920 3 View

Why my mesh convergence is failing in ABAQUS?

I am doing 2D orthogonal cutting simulation in ABAQUS for aluminum. Reducing mesh size up to 0.08 mm reduces the error to 3% but further reduction leads to increase in error from 3 to 39%. Why I...

23 June 2024 9,080 0 View

ABAQUS - Face could not be partitioned. How to resolve this error?

I am doing orthogonal machining of aluminum in 2D. However, when partitioning for depth of cut with a sketch on face strategy with a parting line, it says that face could not be partitioned. How...

18 June 2024 8,000 0 View

My abaqus analysis is not going further a certain time. What can be the problem?

I am trying to simulate orthogonal cutting. My analysis time is stuck at 0.03125 seconds. I killed it and started again. It is again stuck.

27 May 2024 4,917 1 View

How to solve temperature problem in oxley's machining theory?

I am trying to predict cutting forces in orthogonal cutting using Oxley's model using power law in flow stresses. However, I can't get out of the loop where temperature is just changing...

02 December 2023 4,963 0 View

Which is best software to make figures for research and review papers?

I am currently working on research and review papers and need suggestions regarding creating attractive figures.

25 February 2022 9,067 5 View

How to start learning ANSYS and FEM?

I have started learning FEM from scratch. I want to apply it to do numerical simulation of solidification in ANSYS? Where and how to start learning ANSYS?

14 February 2022 8,484 6 View

Can grain boundary be a phase boundary?

I know basic definition of grain boundary and phase boundary. However, can we consider grain boundary as phase boundary as crystal orientation is different?

19 September 2021 1,875 5 View

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,744 4 View

May members post flyers about opportunities to present at a conference? If so, where to post?

May members post flyers about opportunities to present at a conferehttps://veraeducation.com/nce? If so, where to post for the Virginia Educational Research Association? https://veraeducation.com/

08 August 2024 4,584 1 View

How to generate a citation of my paper from ResearchGate?

How we can cite the papers from ResearchGate. I am trying to create citations for this article, Quantum Machine Learning Algorithms for Optimization Problems: Theory, Implementation, and...

08 August 2024 6,688 3 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,599 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,561 0 View

How to get links for copyrights for papers?

how to get links for copyrights for papers?

06 August 2024 7,409 1 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,726 6 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 946 0 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,129 4 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,972 3 View