How stress relieving is done using ANSYS parametric design language (APDL)?

06 February 2013 1 2K Report

After getting the temperature load in structural analysis by LDREAD command, how is the stress relieving done (according to the solidus temperature) using ANSYS APDL?

Debabrata Podder

Stress relieving = An additional loop which will take care of the element activation/ deactivation phenomenon according to the solidus temperature i.e. If temperature < = solidus temperature, elements will be activated in that zone.

Badges
Science topic

More Debabrata Podder's questions See All

How to download the amino acid sequence of a gene from all Arabidopsis ecotypes/accession from 1001 Genomes or any other database?

11 December 2023 1,033 7 View

How does one can distinguish between Donor-acceptor level transition and free to bound by blueshift and redshift in laser dependent PL spectrum study?

I have got redshift in PL spectra for one material and blueshift in another material with increasing excitation power. I want to interpret the DAP and and free to bound transition clearly. Can...

06 July 2023 3,819 0 View

What are the development of geography in Bangladesh?

I don't know. please tell me

23 May 2023 9,360 1 View

Why addition of Zn decreasing the Bending Strength in an Al-Zn alloy?

I have run a 3 point bending test on a Al-Zn binary alloy. The alloy is Al based and Zn is the alloying element. It is noticed that the values of bending strength decreases as percentage of Zn...

04 February 2023 7,145 1 View

How do I should prepare solution for corrosion test of Al alloy in 1M NaCl medium?

Corrosion rate of a Al alloy is going to be tested in NaCl medium. Weight loss method is going to be used. All the specimens are solid bar shaped of cylindrical bar. Should I just prepare solution...

22 January 2023 3,144 4 View

Why does the specimen fail at the grip area rather than the gage area during tensile test?

Dear researchers, I conducted tensile test on Al based Al-Zn binary alloy wherein I found that the failure mainly occurs at the grip area and not at the gage area. At the same time all the samples...

11 October 2022 6,791 5 View

How can congeneric molecules be assembled for 3D QSAR analysis using Schrödinger Software?

I have a dataset of ligands ( from BindingDb databases) that target my protein of interest. For my 3D QSAR study, I wish to classify them into congeneric series of compounds. How can I approach it...

02 August 2022 1,360 0 View

What are the side-effects of inorganic fertilizer on soil biodiversity?

Soil biodiversity is hampering day by day due to various anthropogenic activities. One of them is use of inorganic fertilizer. So are the side-effects?

08 June 2022 3,397 15 View

How to prepare 5% Peracetic Acid at Laboratory?

I want to prepare 5% Peracetic Acid (PAA) from Acetic Acid and Hydrogen Peroxide. Can you please help with the exact recipe? I do not have any PAA test kit. Thanks in advance

27 March 2022 5,201 0 View

Do soil pH and EC are directly or inversely proportional?

Soil pH and EC whether directly or indirectly proportional.

20 February 2022 4,625 3 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View