I am having a difficulty in getting sufficient sample size to run an SEM. Someone suggested a PLS -SEM. Please advise
How "small" can the sample size be for running pls -sem ?
You can refer to my answer for a similar question asked in this RG link.
https://www.researchgate.net/post/What_is_the_minimum_sample_acceptable_for_structural_equation_modelling_using_smartPLS/1
Thank you for the responses
This article can also be very helpful, in general for the use of PLS
http://www.composite-modeling.com/app/download/12407051124/2016_IMDS_Henseler_Hubona_Ray.pdf?t=1452187001
Best regards
Any reference exist on when non directional hypothesis can be used. I'm in a fix between two reaserchers. One says you have to use directional hypothesis other says as you are working on a new...
31 December 2017 3,207 5 View
I am having a sample of firm innovation output and I wish to run an ANOVA Factor 1 : Industry (Ind) - 2 levels Factor 2 : Location - 2 levels - Urban and Rural The sample sizes are Ind 1 -...
04 May 2017 5,475 4 View
Please view the attachment and kindly advise. Some people say use SEM. Some say use ANOVA, followed by path analysis , regression and its variants. Its just a sample of 5 each for the sector (just...
11 December 2016 7,009 4 View
narrative synthesis framework combining existing literature with expert opinion. It seems like combining qualitative data collection with literature review. Please correct my understanding? Is...
09 October 2016 4,314 1 View
Can we use this method without living with participants in their environment
04 May 2016 2,258 5 View
How can technology just be a fad?
01 February 2014 955 1 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
average particle size calculation from TEM
04 August 2024 2,921 1 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View