How is it possible to drive an analytical subthrshold swing model of GAA Fet?

11 March 2017 1 4K Report

Hello

Is it possible to drive a compact analytic model for sub-threshold swing of gate all around FET based on potential profile of it?

I would be glad if refer me to proper examples and papers that did it

Mike Schwarz

Hi,

maybe the following presentation shall give you a starting point. I saw it last year and it deals with some elementary DG structure and the transformation to different ones. As I remember, Jean-Michelle and his group offer several models as we...

http://www.mos-ak.org/lausanne_2016/presentations/T06_Sallese_MOS-AK_Lausanne_2016.pdf

Best

Badges
Science topic

More Reza Meshkin's questions See All

If the emission of all greenhouse gases is stopped now, will the temperature of the earth continue to rise?

Here's a serious question: If we were to stop emitting all greenhouse gases right now, would the Earth's temperature start to cool down, or would the existing greenhouse gases continue to warm the...

30 July 2024 5,123 4 View

How to prepare 100ml solution of 2.5% Glutraldehyde in 0.1M PBS(phosphate buffer) pH about 7, from 25% Glutradehyde and 1X PBS?

final solution volume is 100ml

03 June 2024 417 0 View

How can i use hexamethyldisilazane(HMDS) for drying instead of Co2 and freez drying for SEM analysis of rice anther and pollen?

could you please help with a protocol? should i do it directly on the aluminium stub after dehydration with 100% alcohol or not? should i release the pollen or whole anther is better and dehisce...

03 June 2024 4,793 8 View

Can we create a GVHD model by using stimulated PBMCs and doing co-culture on cell lines?

Hello, I had a question about GVHD. We wanted to investigate the effect of a cytokine in GVHD, but we don't have the possibility to use a GVHD mouse model. Can we do it by using stimulated...

28 May 2024 8,305 1 View

What is the best method to enhance the surface hardness of cutting tools made from SPK steel?

SPK tool steels are used for cutting wires made from low carbon steels. We are searching for a cheap and effective method for increasing the cutting characteristics of the cutters.

14 May 2024 4,948 0 View

Constant Reciprocal of Step Size?

Hello I recently encountered a problem with the reciprocal of step size plot in Comsol Multiphysics. After a certain time (seconds) in a time-dependent solver, the plot oscillations will be...

04 May 2024 7,278 0 View

Poor viability of T cell after transduction with CAR Lentivirus!?

Hi everyone I produced a batch of virus , enriched it with centrifugation, and titrated it with T cells after 48h. For my experiments I want to use MOI 3 and that's equal to 1/12 dilution. but at...

02 May 2024 9,727 3 View

Are you interested in submitting papers to a new journal called "InfoScience Trends"?

InfoScience Trends offers comprehensive scientific content that delves into various facets of information science research. This includes but is not limited to topics such as information...

26 April 2024 9,521 1 View

Does the color of pan traps affect the sampling of flies from the superfamily Bombylioidea?

Garret, 2020 used traps of blue, yellow, and white colors for sampling and collected several specimens.

06 April 2024 6,995 2 View

Laboratory procedures for identifying the concentrations of formic acid and acetic acid in aqueous solutions???

What are the laboratory procedures for identifying the concentrations of formic acid and acetic acid in aqueous solutions using titration, spectrophotometry, or gas chromatography methods...

06 April 2024 187 3 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Is there a good freeware software for photodocumentation of TLC?

I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?

31 July 2024 8,415 1 View

Does anybody know why my chitosan/pva/gelatin hydrogel dissolve in PBS?

My final research is about making chitosan/pva hydrogel for wound healing using gelatin as crosslinker. Last month, i made the thin film hydrogel and it turn well. It was okay. Last week, i make...

28 July 2024 2,794 6 View

How can I calculate AlGaN/GaN HEMT Breakdown Voltage on Silvaco TCAD?

Hello, I'm newbie to TCAD. I wanna calculate Breakdown Voltage of AlGaN/GaN HEMT. But, my code shows just saturation. Could you please help me how to simulate Breakdown Voltage of my code? And...

25 July 2024 3,738 1 View

How can i solve the code problem in Sentaurus TCAD?

Currently, I have created a gate-all-around process using sentaurus tcad and I am trying to measure the noise using the cmos noise code. However, an error occurred during the simulation. The error...

24 July 2024 6,352 0 View

How can I better use imageJ to get good result on calculating surface area of a film accurately?

I have images of film formed on the bottom of a 50mL beaker, and I have been trying to figure out the surface area. I could easily use features on imageJ to do that, but I want to know which area...

23 July 2024 4,461 1 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View