How does TiO2 help in calcination of Alumina?

25 December 2019 1 7K Report

Calcined Alumina is produced in the industrial kiln from bayer Alumina Tri-hydrate and mineralizers are added to lower its calcination temperature. They also affect the particle shape and size.

Alexander Jun Wang

Refer to the attached thesis - the conclusions should be helpful.

Badges
Science method

More Reshma Kuppili's questions See All

What are the methods for analyzing trihalomethanes in water other than gas chromatography and liquid chromatography?

for monitoring disinfection byproducts in drinking water

12 October 2023 8,613 3 View

I am doing base hydrolysis of ester with LiOH and THF:H2O( 1:1) but after hydrolysis in acid NMR I am getting 4 proton extra peak?

4 protons peak may be CH2 near a heteroatom .

13 July 2023 1,075 1 View

How to reduce air bubble formation in film?

The film forming solution (FFS) is stirred overnight and it is oven dried at 40°C. Please give me suggestions to reduce the air bubble.

09 July 2023 7,857 4 View

Does anyone know how to prevent protein coeluting with other impurities in size exclusion Column?

I have been trying to purify a transcription factor. Protein has MBP and His Tag. I use His TRAP as my first purification step and then after I do size exclusion, but my protein (83 KDa) elutes...

23 April 2023 9,182 5 View

How to recover the Pd(PPh3)4 catalyst, already become dark brown?

How to store this catalyst?

06 March 2023 9,026 1 View

How do I determine doping concentration of a new element in Barium Titanate structure if I want to produce a new system?

I want to produce a new system of Barium Titanate and characterize it for high dielectric constant values at microwave frequencies.

02 February 2023 4,203 8 View

How to find Yaw joint angle of differential drive robot ?

I'm designing leader follower feedback controller for crawler robots .Here rear wheel is connected to front via a joint so that it can follow front when it turns ,for both the module(front...

20 December 2021 1,203 3 View

Multivesicular liposomes formulation?

multivesicular liposomes are prepared by double emulsification method. Can someone tell how to evaporate organic solvent from multivesicular liposomes preparation without emulsion cracking?

04 March 2021 5,166 3 View

What might be the reason for obtaining two bands in plant genomic DNA extraction?

I got a thin band and a thick band i guess it would be the genomic DNA and the 260/280 ratio is 3.

21 February 2021 6,871 6 View

Any recommendations for tetR antibody for IHC?

I am planning an experiment where I've to detect cells which are expressing TetR, my vector is so big that I can't have a reporter in it. I was thinking if I can detect the expression of TetR...

24 September 2020 1,293 4 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

Need heterogeneous catalysts calcined before reduction?

Metal-containing heterogeneous catalysts often need to be calcined before reduction, so what are some examples of catalysts that perform better without calcination? What is the reason and how many...

05 August 2024 909 2 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

Why am I observing very high Temperature and Pressure Increase using NPT Ensemble?

Hello everyone, I am running DFT with CP2K software at 1200 K, 1 bar with a periodic system of 64 Al atoms + 2 CO2 atoms. However, I am seeing my temperature slowly increase to >4000 K and my...

22 July 2024 3,177 0 View

A twin-shaft kiln or a rotary kiln for lime production 1 class? if compressive strength of limestone is low 60 MPa?

My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...

18 July 2024 1,390 2 View

Can we calculate the CO2 adsorption capacity(mmol/g) of a solid adsorbent (MOF) using CO2_TPD analysis?

what is the relationship b/w TCD signal(a.u) and CO2 desorbed (mmol/g) ? can we plot CO2 desorbed(mmol/g) Vs Time(min) from TPD data?

15 July 2024 3,248 1 View

Could Nd doping into TiO2(anatse) because Nd's dense diameters are bigger than in TiO2 ?

could Nd (Neodimyum) doping into TiO2 because Nd's dense diameters are bigger than in TiO2

11 July 2024 2,350 2 View

Determine pore diameter by BJH of TiO2?

Dear all, l need to help me to determine pore diameter. I got from BJH data the rp(peak area), Desorption Isotherm was 1.6 nm, but from Isotherm l got type lV with hysteresis H2 loop. Can l used...

10 July 2024 2,872 1 View