What are the equations of the boundary layer of a flat plate that TDMA method is based on?

Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...

05 June 2019 7,941 4 View

How to define a heat flux and convection coefficient at the same time on a wall using user defined function in FLUENT?

Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!

05 June 2019 7,041 12 View

How can we define a symmetry wall boundary condition in Fluent?

Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...

04 May 2019 5,819 3 View

How to use Chemkin to model the model studied in the attached paper?

Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks

04 May 2019 3,934 2 View

Can we cople between ANSYS FLUENT and Simplorer ASAP?

Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!

03 April 2019 2,674 6 View

How can we define a heat flux boundary condition + convection for one wall in ANSYS FLUENT?

Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks

02 March 2019 5,946 4 View

What are the equations used to simulate a steady state thermal analysis using FEA ANSYS thermal?

Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks

31 December 2018 5,790 5 View

How can we save calculations to a text file from a Matlab CFD code during running the code like ANSYS FLUENT?

Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!

31 December 2018 816 3 View

How to save data in a file from MATLAB GUI?

Hello, we have a MATLAB GUI code and it produces a graph, we need to save the data of the graph in a txt file, how can we do it? Thanks

09 October 2018 6,552 4 View

How to plot data from a table written in a txt file using MATLAB?

Hello, I have a file contains many columns and we need to plot the table in MATALB. How can we do this? The file is attached.. Thanks

09 October 2018 1,032 0 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View