Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

What kind of food stuff increase the potentiality of human brain?

There are different kinds of food stuffs which we intake daily according to our requirements. Carbohydrate, protein, fat, mineral, vitamin, water are mainly working for the growth and development...

01 March 2021 831 2 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

How can we theoretically calculate Elemental analysis(percentage) of atoms in covalent organic framework?

For example in one research article the Elemental analysis values of COF-TpPa-1 ( Triformylphloroglucinol (Tp) (63 mg, 0.3 mmol), Paraphenylenediamine (Pa-1) (48 mg, 0.45 mmol) are as follows...

24 February 2021 1,265 6 View

Is there any teachers based in UK who would like to take part in my study?

24 February 2021 4,833 3 View

Amorphous silica XRD peak at around 10 degree?

21 February 2021 3,417 5 View

SSR primers are species specific or we can use it for any plant species ?

Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...

20 February 2021 315 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Steps to calculate activation energy by coats & redfern method?

I'm a chemistry student and I'm researching the kinetic degradation of mixed plastic waste. I'm having trouble calculating the activation energy by the coats & Redfern method. The data that...

24 February 2021 974 1 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View