How do I plot pressure variation using FFT (Fast Fourier Transform) in Fluent?

More Puneet Nema's questions See All

How can I create baffle in ANSYS Design Modulur?

I am facing problem in creating geometry. My problem includes a rectangle with one vertical baffle inside. Initially I was creating a solid body and then using new plane. I am creating surface...

03 April 2014 4,968 5 View

Can anyone tell me how to create animation in fluent using data files after simulation has already been done?

I have tried in cfd post but not able to do it properly.

11 December 2013 5,179 3 View

Multiphase flow - can anyone help?

I want help regarding writing udfs. My problem is basically regarding liquid sloshing. I want to simulate sloshing phenomenon in a rectangular tank having two types of motion. 1-sinusoidal...

10 November 2013 9,097 4 View

Is the courant number fixed at 0.00 while iteration?

I am simulating liquid sloshing problem in ANSYS FLUENT. But while calculating (iteration), global courant number remains at 0.00 and it is not changing and hence there is no movement seen in any...

10 November 2013 2,390 15 View

UDF for sloshing rectangular tank

I have written UDF for sinusoidal wall movement given to a 2-d rectangular tank of dimension (3*3), but after iteration it doesn't show any results or movement in water phase. I have tried...

10 November 2013 416 1 View

Liquid sloshing - can anyone help?

What will be the boundary conditions for a 3D rectangular geometry in liquid sloshing problem?

09 October 2013 9,803 2 View

What is the meaning of time steps in Ansys 13.0?

While doing simulation for unsteady state fluid problem, we use time intervals and time steps in fluent. What is the concrete meaning of these terms?

09 October 2013 6,511 11 View

What are the mathematical equations related to liquid sloshing phenomenon?

What are the mathematical equation related to liquid sloshing phenomenon except continuity and momentum equations and what is the physical significance of these equations?

09 October 2013 3,705 3 View

Liquid sloshing?

I want to start work on sloshing in a rectangular overhead tank filled with water. Motion in the tank is due to earthquake and I want to simulate it using Ansys 13.0. I'm not able to understand...

09 October 2013 3,077 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Abdelkrim Merzougui

1. You can use software GAMBIT to create the geometry and to mesh.

2. Used the fluent for plotting pressure variation at a certain point vs frequency.

Puneet Nema

thanks sir for ur reply...i have created geometry and sone simulation in fluent...now i want to use FFT to study pressure variation w.r.t frequency.

Done*

Arturo Ocampo

Hello Could you explain how you did?

Hussam Ali Mohammed

Good question.. Please share me the best answer might you trust...

Regards…