How do I get a friction map?

More Roobala Chelladurai's questions See All

Is it possible to recycle the Shampoo?

I have heard that the shampoo which is about to expire can be recycled into to cleaning agents etc. Is that possible ? What is the process? Also, most of shampoo has oil in it. So, how will the...

16 August 2023 9,658 2 View

Precedure for cleaning TGA crucibles?

We performed a few TGA measurements on MOFs and faced severe contamination of crucibles at the end of the tests. Please let us know an effective cleaning procedure to follow. We tried Aqua regia...

25 October 2022 4,183 3 View

I have to publish the full manuscript in same journal or shall I publish in it different journal?

I published a abstract in conference proceedings..

02 May 2020 2,831 5 View

Are there any specific sub-phase conditions to be maintained in case of DPPG monolayer?

I am facing some issue with preparation of DPPG supported monolayer and bilayers using Langmuir Blodgett technique. They are not getting transferred efficiently as opposed to PC lipids. We also...

17 April 2018 2,050 1 View

Is anyone having the design guidelines for clutch housing with ventilation concept?

If you have the design guidelines for clutch housing with ventilation concept, kindly share me the guidelines. For my project heat dissipation is more. So we are planning to ventilation in the...

18 February 2018 3,609 0 View

Is it possible to include damage model into the Viscoelastic material model?

I'm trying to simulate Adhesive failure using Abacus.

11 October 2017 1,416 0 View

What are the calculation has to be done for clutch(car)

Like Heat stress, clamp load and pedal effort

22 June 2017 9,700 3 View

In my project clutch heat stress( Calculated) exceeded , is there any possible to reduce the heat stress without changing the vehicle specification.

Like surface roughness, coefficient of friction

22 June 2017 3,652 4 View

Any one give the clutch and release system design manual

1. Clutch heat stress calculation2. Clutch clamp load calculation3. Pedal effort calculation4. Pedal assistance calculation

22 June 2017 4,255 2 View

How to calculate mean molecular area(MMA) for binary / ternary surfactants in Langmuir trough?

We are using KSV NIMA Langmuir trough for forming Langmuir monolayers. If we can input the molecular weight(M.W), volume(v) of solution and corresponding concentration(c), MMA is calculated from...

02 April 2017 4,770 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View

jean-louis Gerstenmayer

It seems to be a genius idea, Go ahead !

Roobala Chelladurai

I hope its not a sarcastic comment..!!

We can say 'It seems a priori to be an interesting' idea .... Obviously, it must be validated by your team, according to the real experimental incomes, situations may be complex & diverse :

http://www.nature.com/srep/2015/150109/srep07698/full/srep07698.html

http://pubs.acs.org/doi/full/10.1021/jz502188g

......