I have to publish the full manuscript in same journal or shall I publish in it different journal?

I published a abstract in conference proceedings..

02 May 2020 2,658 5 View

Percentage of DMSO?

Hi everyone Idisolved my drug 3mg in 1ml DMSO and I take 20uL from it and I dissolved in 10ml cell culture media then I make serial dilution 2 fold and I did the same thing with DMSO. But it...

02 November 2017 3,799 2 View

What are the calculation has to be done for clutch(car)

Like Heat stress, clamp load and pedal effort

22 June 2017 9,382 3 View

In my project clutch heat stress( Calculated) exceeded , is there any possible to reduce the heat stress without changing the vehicle specification.

Like surface roughness, coefficient of friction

22 June 2017 3,511 4 View

Is it possible to obtain the exact compound structure in ReaxFF MD simulation?

Because i have performed all my simulations at a time step of 0.50 fs (also varied the time step between 0.25-0.50 fs). After analyzing the thermal decomposition results, I was not able to match...

09 January 2017 3,131 7 View

How can I check the Na is doped in ZnO or not?

22 June 2016 3,879 4 View

Is the numerical value of positron diffusion constant different from surface to bulk of the solids?

If I consider positron diffusion length L+ is constant through the solid. But by VEPFIT I am getting two layer (surface and bulk) of the solid

02 February 2016 1,270 1 View

No title

Can anyone suggest me some ways?

14 March 2014 2,093 3 View

Mathematical Models of neurons

I have in the past wrote a softwre that simulate a neural network based on Hebb model. Means that electrical impulsions processed by a neuron (physically speaking) could be translated bya...

10 September 2011 3,293 7 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Hello house, is it necessary to compute Content Validity Ratio (CVR) for an adapted questionnaire pls?

What should one do if he obtains conflicting results between Content Validity Index (CVI) and CVR for items in a quetionnare. For example based on the CVI obtained the items are acceptable but the...

25 February 2021 7,325 2 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View