I have to publish the full manuscript in same journal or shall I publish in it different journal?

I published a abstract in conference proceedings..

02 May 2020 2,658 5 View

Percentage of DMSO?

Hi everyone Idisolved my drug 3mg in 1ml DMSO and I take 20uL from it and I dissolved in 10ml cell culture media then I make serial dilution 2 fold and I did the same thing with DMSO. But it...

02 November 2017 3,799 2 View

What are the calculation has to be done for clutch(car)

Like Heat stress, clamp load and pedal effort

22 June 2017 9,382 3 View

In my project clutch heat stress( Calculated) exceeded , is there any possible to reduce the heat stress without changing the vehicle specification.

Like surface roughness, coefficient of friction

22 June 2017 3,511 4 View

Is it possible to obtain the exact compound structure in ReaxFF MD simulation?

Because i have performed all my simulations at a time step of 0.50 fs (also varied the time step between 0.25-0.50 fs). After analyzing the thermal decomposition results, I was not able to match...

09 January 2017 3,131 7 View

How can I check the Na is doped in ZnO or not?

22 June 2016 3,879 4 View

Is the numerical value of positron diffusion constant different from surface to bulk of the solids?

If I consider positron diffusion length L+ is constant through the solid. But by VEPFIT I am getting two layer (surface and bulk) of the solid

02 February 2016 1,270 1 View

No title

Can anyone suggest me some ways?

14 March 2014 2,093 3 View

Mathematical Models of neurons

I have in the past wrote a softwre that simulate a neural network based on Hebb model. Means that electrical impulsions processed by a neuron (physically speaking) could be translated bya...

10 September 2011 3,293 7 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View