Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Does heat in goat affected by feeding or BCS of the animal?

Does feeding affect heat in animal? if we were to add a specific feed (with data on dry matter content), how can we correlate feeding to estrus?

10 January 2021 9,719 13 View

Why the presence of surface active compound repress the mass spectra of other compound? If the sample is itself surface active, then self repression?

I am assuming the resulting insertion/agglomeration in the presence of a surfactant or the agglomeration of surfactant may reduce the rate of ionization. The mobility of the ion may also be...

07 January 2021 987 5 View

What are various Thermal Insertion Materials?

I am working on a project of heat Sink. What are different insertion / filling materials I can use? Suggest some material about it. Thankyou

28 December 2020 728 3 View

How to prepare methylcellulose based semisolid media for cell culture?

Does anyone know how to prepare methylcellulose-based semisolid media for cell culture? Which one to use 15cp or 1500cp?

10 December 2020 5,266 2 View

What are all the criteria for the occurrence of Lunar Eclipse?

I have read the maximum limit of Lunar Eclipse is 12.2 degrees of arc (i.e. the difference in the longitude between Moon and any one node of the Moon). However on on June 5th 2020, a partial Lunar...

27 August 2020 986 5 View

What is the need to run the optimization code for multiple times? What will be the outcome for this multiple runs?

Dear all, I have to know what is the need to run the optimization code for multiple times... For example, I m implementing a new variant optimization algorithm, I am setting maximum number of...

19 July 2020 6,004 4 View

Can anyone know how to do 1D ground response analysis using COMSOL multiphysics 5.4 ?

I want to compare results of 1D ground response analysis of DEEPSOIL and COMSOL

05 July 2020 3,014 2 View

No title

16 June 2020 2,168 1 View

What is the current status on regulatory approvals of COVID-19 vaccines?

What is the current status on regulatory approvals of vaccines meant for COVID-19 according to USFDA, EMA, TGA, etc?

10 June 2020 7,582 5 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

How to get rough estimation of the concentrations of Oxygen and moisture inside the glove box?

Dear colleagues, I was just wondering if you can suggest a good method to get a rough estimation to the concentration of O2 and H2O inside the glove box as unfortunately, our glove box doesn't...

17 February 2021 1,012 3 View

Is it reliable to evaluate surface roughness (gwyddion) with SEM pictures?

There are a few works(e.g. DOI 10.1002/sia.4889) reporting that surface roughness can be evaluated by software like gwyddion with SEM pictures.However,the surface roughness is strongly influenced...

09 February 2021 1,905 8 View

Is it possible to find out the wettability and contact angle of water on the rough or corrugated substrate?

First of all, whether it is possible to identify the presence of water and its amount on the Silicon substrate by using only FT-IR spectroscopy. Can ATR-FTIR spectroscopy find out the wettability...

03 February 2021 9,085 4 View

Among all the environmental pollutants globally how much % out of 100% is due to chemists?

Environmental pollutants and hazardous are major issues through which the modern world is suffering. Among all the environmental pollutants and hazardous materials how much contribution is from...

31 December 2020 6,039 3 View

Among All the environmental pollutants how much % out of 100% are due to chemists?

Environmental pollutants and hazardous are major issues through which the modern world. Among all the environmental pollutants and hazardous materials how much contribution is from chemists (out...

31 December 2020 833 7 View

How do you describe the effect of surface roughness in 3 point bend simulation in Abaqus?

Hello everyone, Part of my project is to investigate the effect of surface roughness on stainless steel 17-4 PH in a 3-point bend simulation on Abaqus. I was to use 2D planar mode and manually...

21 December 2020 5,675 3 View

Precise film thickness?

Dear all, I am wondering how is the precise way to determine the film thickness from the cross-section of SEM with a certain degree of surface roughness? Shall I determine the film thickness...

19 November 2020 5,752 3 View

Why thrust force, temperature and surface roughness increase with feed rate in Machining?

Reasons why thrust force, temperature and surface roughness increase with feed rate in Machining?

17 November 2020 873 4 View

How can I decrease surface roughness in selective laser melting?

Recently, I study master degree in Taiwan. And my research topic is about metal 3-d printing with in718. I am required to decrease surface roughness in overhanging structure or inclined cube. Is...

02 November 2020 8,127 3 View