How could I 'undo' during using ABAQUS software?

More Hiba al-adhami's questions See All

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

Is there a fast method matching citations to bibliography (manually typed references)?

I need to be able to match in-text citations to a reference list and back again in very large documents (100+ pages) WITHOUT the use of referencing software like Endnote. my method is to type the...

27 February 2021 9,848 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

What is the most suitable medium of ascomycetes fungi ??

26 February 2021 4,413 1 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Is it possible that Cancer cells could survive in heparinized blood for 48 hours?

Hi everyone, I am just wondering if we incubated 200 microliter of whole blood with 50 microliter of cancer cells(1bout 5000cells) do you think that cancer would survive for 48 hours?

23 February 2021 3,840 3 View

What is the most prevalent drug related problem in the developed countries?

Detecting the drug related problems is an important step in the pharmaceutical care plan

21 February 2021 5,421 3 View

What are the dimensions by which the independent variable (big data) can be measured, Knowing We using the questionnaire instrument?

We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...

21 February 2021 8,133 2 View

Is nanotechnology part of materials science? Is it possible to obtain Pico technology and move from hypothesis to application?

Pico-scale This is three orders of magnitude smaller than a nanometer (and thus most nanotechnology) and two orders of magnitude smaller than most chemistry transformations and measurements. Pico...

18 February 2021 4,540 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View

Mehdi Lima

There is not such an "Undo" like what we have in "Microsoft Word". You should go to the part section and define your model .

Behzad Dastjerdy

you have to go back your sketch and correct your mistake! in the other modules like property, assemble and etc, the only way to correct your mistake is just "Edit menu"!

Hiba al-adhami

Thanks and I appreciate your response.