How can we use the Duncan Chang model in comsol?

08 August 2018 0 10K Report

Has anyone tried to use the Duncan Chang Model for 2D model in comsol multiphysics? Could anybody send me an example? i did find it under nonlinear elastic material but could not successfully implement it.

Badges
Science topic

More Chandan Shakya's questions See All

Has anyone managed to install Abaqus 2019 on manjaro linux?

I'm trying to install abaqus on manjaro Linux but have been unable to do so. In the Linux.sh file I commented out the DSY_OS_Release=`lsb_release --short --id |sed 's/ //g' line and replaced it...

09 October 2019 476 2 View

Can anybody tell me how use the duncan cahmg model with comsol to simulate a triaxial test?

I have been trying to simulate a triaxial test of rockfill from a research paper for a while now. I have made the parameters of the duncan chang model i.e. the young's modulus, bulk modulus and...

11 December 2018 8,274 0 View

Can anybody tell if there any upcoming conferences on Civil, Geotechnical or Dam Engineering?

I have been looking for conferences for a while now and I started reading about predatory conferences. Now I am not sure which conferences are genuinely legitimate? There are not many sites that...

10 November 2018 433 7 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Can we recognize signs of the "volatility clustering" property of a time series in its time domain plot?

My purpose is to recognize the volatility clustering property without statistical tests such as The Lagrange Multiplier (LM) test.

24 February 2021 4,150 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View