How can we derive a formula using gene expression programming?

More Arbab Faisal's questions See All

Is it possible to calculate the mass of the steel building by using the accelerometer data?

I tested a 5 story steel frame on a shake table. but I forgot to calculate the total mass of the building. Can I calculate it by using the accelerometer data? if yes, Please help. Thanks

03 April 2018 5,118 3 View

How to make sure that concrete is properly compacted in concrete filled steel tubes?

I just casted concrete filled steel tubes. In order to avoid segregation, I tilted the tubes at approximately 60 Degrees and then insert concrete inside. Now is there any kind of test for making...

07 August 2016 2,895 21 View

Filling of hollow steel beam with concrete

I want to fill rectangular hollow steel beam with concrete. The problem is that length of the beam is 3m. Can you give me some suggestions on how to fill it vertically? As throwing concrete from...

05 June 2016 7,954 5 View

How can i design concrete filled steel tube in ABAQUS?

For Research purpose

05 June 2015 5,355 7 View

How to draw moment-curvature curve for composite beams when load-deflection curve of the beam is available?

I performed experiments on Concrete filled steel tubes. Got the results in the form of load-deflection curves. Now, I want to convert them to moment-curvature curves for the purpose of comparison...

01 January 1970 7,222 12 View

Will there be any difference in stress-strain curves of concrete cylinders and cubes?

If we use concrete cubes instead of concrete cylinders for finding the stress-strain curve, what effect it will produce? Will both be the same or will there be an effect of h/d ratio?

01 January 1970 3,995 10 View

How can we compare the load-deflection curve of two beams having same cross-section and different length?

If we have two beams having same cross-section and boundary conditions but different lengths. How will we compare their load-deflection curve? Or in simple words, how to convert the...

01 January 1970 9,426 16 View

How to calculate the yielding stress in concrete filled steel tubes?

Recently I tested concrete filled steel tube of 3.5m length for flexure load. When the maximum deflection at the center reaches to 20mm, the machine broke down. Now I want to check that whether...

01 January 1970 4,108 5 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Request Python code?

Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!

08 August 2024 6,242 2 View

Why does everyone use vs code?

Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...

07 August 2024 7,013 4 View

Why did the authors extrapolate a phenotype that they experimentally proved in one bacterial strain across the whole genus of the organism?

I aim to be as skeptical as possible regarding whether a pair of orthologous genes results in the same phenotype in their different but related bacterial organisms under similar environmental...

05 August 2024 6,787 4 View

Why my colony PCR results of my recombinant bacterial not showing any results?

I am performing ligation of the plasmid and a target gene. The steps I have taken are: 1. Double digestion of the plasmid and target gene 2. Ligation of the plasmid with the target gene 3....

05 August 2024 2,570 3 View

How can i do multivariate Time Series forecast using MLP, ANFIS and LSTM?

I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.

05 August 2024 2,977 3 View

What is the acceptable p-value cutoff for GO enrichment analysis ?

I have an RNA-seq data that I have analysed using Limma-voom and have extracted the gene IDs, log2FC and the p-values. At p value < 0.05, I have over 10,000 DEGs, however, when I run the GO...

31 July 2024 225 2 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

What are the steps of formulating a herbal extract into a sheep/goat drench?

I am working on natural remedies for de-worming in small ruminant livestocks. Part of my project involves formulation of drench-type product, which I have not much experience in. My experience is...

30 July 2024 9,806 1 View