How can the axial velocity of water jet be calculated inside 3-D mixing tank?

12 December 2017 1 4K Report

The 3-D mixing tank contains water as a storage medium. It is required to create turbulence in the tank by inserting a jet of high velocity water through a nozzle located inside the tank. How can the software (ANSYS FLUENT) be used to estimate the axial velocity component at the nozzle exit?

Mahesh Nagarkar

Refer

https://www.google.co.in/url?sa=t&source=web&rct=j&url=http://www.tandfonline.com/doi/pdf/10.1080/19942060.2008.11015218&ved=0ahUKEwiD8MCGhq3YAhUDvY8KHSXvAQYQFgglMAA&usg=AOvVaw3ixH1ys8VJe0p_jvhVXlRv

Badges
Science topic

More Hayder Jaffal's questions See All

No title

The performance of heat exchanger can be substantially improved by a number of augmentation techniques. One of these methods is Nanotechnology. Nanofluid widely used to enhance Nusselt number...

11 December 2017 7,660 13 View

How can I calculate the characteristics length in radial heat sink?

For natural convection heat transfer of the heat sink with different fin configurations such as straight radial fins and pin fins, how can I calculate the characteristics length in radial heat...

11 December 2017 1,933 3 View

Is it possible that the pressure is proportional to the velocity?

When solving the Navier-Stokes equations for a fully-developed viscous flow in a straight channel, we noticed that the velocity and pressure changes along the channel direction. Is it possible...

11 December 2017 3,775 9 View

What are the most important factors limiting the installation and use of wind turbines to generate electricity in a particular area?

Wind turbines convert the kinetic energy in the wind into mechanical power. This mechanical power can be converted to electricity.Wind turbines have been used as a source of renewable energy for...

01 January 1970 9,265 4 View

What is the relationship between the exergy and the pumping power?

In view of second law of thermodynamics, to optimize the performance of any thermal system, it is important to analyze the exergy of this system by making exergy balance between the system and the...

01 January 1970 7,415 14 View

How can I present many contours in one figure using ANSYS fluent?

I have temperature contours for different cases and I would like to compile them in one figure to show differences between them. How can I present many contours in one figure using ANSYS fluent?

01 January 1970 1,215 4 View

Practically, using nanoparticles with PCM is an effective method to Improve performance for those materials?

Using nanoparticles in phase change materials (PCM) Improves thermal conductivity. Increased thermal conductivity allows for a faster rate of heat transfer in PCM, reducing the time required for...

01 January 1970 2,060 10 View

Is there any paper related to bioheat transfer from wireless devices?

The wireless devices have become the integral part of our everyday life. These devices are being used for many purposes such as for Internet and Telecommunication. There are many effects of...

01 January 1970 4,034 7 View

What is the reason for the number of citations (for the same papers) different in both ResearchGate and Google Scholar?

Some papers has citations in the ResearchGate, and these citations do not appear for the same papers in the Google Scholar, and some research shows the opposite. What is the reason for the...

01 January 1970 9,990 0 View

Which method is best to improve heat transfer in thermal systems : increase surface roughness or surface coating with nanoparticles?

Surface roughness is used to improve heat transfer in thermal systems. On the other hand, surface coating of nanoparticles improves heat transfer. Which method is best to improve heat transfer in...

01 January 1970 7,413 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View