How can nucleation and growth of coating be investigated by chronoampherometry?

More Tahere Golizadeh's questions See All

How to use Abaqus XFEM analysis under high cycle loading?

I want to do crack growth analysis by X-FEM ABAQUS under cyclic loading. The applied stress level is in the HIGH CYCLE range. I know about STEP available for FATIGUE in ABAQUS (Direct cyclic), but...

25 June 2023 9,935 4 View

What should I do to reduce genomic DNA in RNA Samples?

I do phenol-chloroform RNA extraction. But after running the samples on gel electrophoresis, I see more DNA. What should I do to reduce genomic DNA during RNA extraction?

26 January 2022 6,591 8 View

Topology include file " " not found?

Dear all, I am trying to simulate an organic system. when I try to add ions, I faced the following error: Fatal error: Topology include file "tryptophan.itp" not found I modified my .top file as...

25 January 2020 8,833 1 View

How can an coating composition be determined before electrodeposition by electrochemistry?

In a binary or a triple alloy coating I do want to investigate and estimate the coating composition before electrodeposition.

16 December 2019 4,884 5 View

What's the advantage of double layer coating prepared by electrodeposition to multilayer coatings?

I do want to deposit a double layer coating by DC electrodeposition.

06 September 2019 7,255 3 View

How can current efficiency of electrodeposited alloy coating be determined?

14 May 2019 5,718 4 View

What is the proper distance of the cathode and anode in electrodeposition?

How can this distance be determined?

31 December 2018 9,537 4 View

Reduction carboxylic acid to aldehyde

What is the method for reduction carboxylic acid to aldehyde and measurment by HPLC and second stage derivatization aldehyde by 2,4-dinitrophenylhydrazine?

06 July 2012 8,820 5 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

Why can't we get on top of this incubator infection (fungal)?

We have been experiencing repeated what looks very much like fungal contaminations in several incubators (in the same lab). We have tried the following repeated times and yet the coating on all...

02 July 2024 6,375 2 View

How to load Remedesivir drug into mesoporous nanoparticles?

Hello, I want to load Remedesivir (RNA polymerase inhibitor) into mesoporous nanoparticles (MSNs). The issue is drug is temperature and pH sensitive and it degrades quickly. I need advice on its...

01 July 2024 889 3 View

Vahhab Ghafourian

what is

Chronoampherometry ??

Tahere Golizadeh

Juan Genesca

Thank you for your helpful comment.

Chronoamperometry is an electrochemical technique in which the current is monitored as a function of time in an electrochemical cell. It can be done in a contant potential or in a double step potential.