Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

Permanganate oxidizable carbon pH adjustment ?

03 February 2021 1,706 2 View

Interpretation of Posterior distribution produced by MCMCglmm?

Dear all, I have a comparative phylogenetic model on MCMCglmm, with a binary response variable, 4 binary explanatory variables as fixed effects and the phylogeny as a random effect. I would...

29 September 2020 2,165 2 View

How to analyze differences in short-, mid-, and long-term improvements between two groups?

Hello folks! We created two training courses: A (N=25) and B (N=25). Participants were assigned to one of the two groups respectively. They were tested before, shortly after, and 3 months after...

13 July 2020 2,903 3 View

Did anyone find the right input for mush parameter (Amush) in solidification and melting model of ANSYS FLUENT?

Hello! I am currently involved in a Direct Chill Casting Model of an Aluminum Alloy. The model was built both in ANSYS FLUENT and in COMSOL. I am facing convergence issues and i cannot find the...

23 April 2020 8,253 1 View

Is it possible to couple fluid flow, heat transfer, phase change and mechanical stresses on the solidifying shell using COMSOL Multiphysics?

I am trying to simulate DC Casting of Aluminum Alloys in Comsol. I found an example related to Continuous Casting that it couples fluid flow, heat transfer and phase change during solidification...

28 March 2020 3,010 4 View

Is there a protocol for a multicolour fluorochrome cell staining in microplates?

Our laboratory is not equipped with a flow cytometer. Is it possible to stain cell suspensions (i.e. from thymus) in 96 well plates with multiple fluorochrome conjugated antibodies and then read...

23 February 2020 1,566 3 View

BaysTraits analysis: Using random sample of trees or most probable trees?

Hello. I want to run an MCMC analysis on BayesTraits using a set of Bayesian trees I created using MrBayes. I want to run the analysis using both the consensus tree and a sample of 1,000 trees to...

28 July 2019 5,860 2 View

Can you specify the gene type in a partition file?

Hi! I am trying to build a phylogeny using a mixture of mitochondrial and nuclear protein-coding genes and rRNA genes. Is it possible to specify the specific type of gene in the partition file? I...

16 December 2018 6,033 3 View

Step by step calculation of Lithium Diffusion Coefficient using EIS measurement ?

Hello ! I am trying to figure out how Dli (Lithium diffusion coefficient) is calculated. A method is from EIS measurement. Specifically, from the relationship between Warbung impedance and the...

06 December 2018 9,455 11 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View