Dears,
I would like to show the principle stress of all nodes in my model using workbench directly without exporting to excel sheet. how can I do it?
I have exported a model with all boundary condition and meshes from ansys workbench to abaqus. the imported model has the same meshes and fixed boundary as in the ansys but the applied force did...
31 December 2018 9,160 0 View
What chemicals should I use to increase the wettability of nanoparticles the nano are carbon tubes, alumina, silica. The adhesives are wooden glue and epoxy.
11 December 2018 3,735 0 View
Dears, I want to conduct a research about composite materials. in my work I have 5 parameters with 4 levels but the problem is that some of the parameters have only two or three levels (see table...
11 December 2018 5,167 5 View
Using hot spot stress to calculate the stress concentration factor require that 2 gamma which is the chord width to thickness ratio in square hollow sections/ t- joint welds to be greater than 12...
10 November 2018 3,734 1 View
Hi, I am simulating the effect of design parameters on welded joints. Despite that, I applied only 1KN.m bending moment on the model but the out put Von Mises stress values are abnormal and of...
08 September 2018 2,109 10 View
despite that, I have tried many methods to solve the issue of abnormal stress values around weld joints but all didn't work. why? I applied 100 KN lateral force at the top and fixed the model from...
08 September 2018 624 0 View
1. what is the reason of the aforementioned warning? 2. how can I solve the problem? 3. what is the effect on the results? hint: I am working on welded joint under fatigue load using mechanical...
08 September 2018 8,372 3 View
Hi, using stress strain data of uniaxial tensile test, I fitted the curve using Mooney- Rivilin 5 parameters method of hyperelastic materials. But when I run the program a warning message appears...
05 June 2018 8,159 0 View
hi, I'm investigating the effect of impact on the mobile cover which is made of hyperelastic rubber using explicit dynamic workbench. The curve of tensile test was fitted using 5 parameters...
04 May 2018 3,856 3 View
Hi, it is well known that respected journal indexed by Thomson Reuters do not accept citation from webpages. So I wonder if there is an original site that can provide me with Modulus of...
04 May 2018 1,856 6 View
I attempted to make a privately uploaded text public but a window appeared that said an error occurred. There was no explanation provided as to why there was an error or what might be done to...
05 August 2024 8,025 7 View
I have incorporated the dispersion effect for the OPBE functional by specifying the S6, SR6 and S8 parameters for GD3 in Gaussian G09 package. For this purpose, I have defined the environment...
05 August 2024 1,494 2 View
What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...
02 August 2024 3,174 1 View
I am a student in a master's program for Special Education and I am curious to see what Evidence-Based Practices that are used in teaching individuals with Autism Spectrum Disorder benefit from...
30 July 2024 5,611 1 View
Hello , I established a stable cell line expressing GFP tagged to a centrosomal gene having G418 drug selection marker. I validated the stable line by IFA and Western blotting, results are fine....
29 July 2024 5,007 0 View
DOS version.
29 July 2024 6,064 1 View
I have reached out to the original creator Dr. Demerouti but have had no luck with a response. I am completing my IRB form and need the information or permission by tomorrow. I know short notice,...
29 July 2024 3,684 0 View
I need a reliable source or an example supported by excel sheet to understand Fuzzy Vikor?
27 July 2024 5,916 1 View
i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....
26 July 2024 1,887 0 View
The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.
25 July 2024 9,976 3 View