How can i show SRSS modal combination results in ansys apdl due to spectrum analysis?

More Mohamed Hassan's questions See All

In ansys apdl what is the difference between single point response spectrum and multi point response spectrum ?

in ansys apdl what is the difference between single point response spectrum and multi point response spectrum ?

02 March 2019 7,985 2 View

Problem Response spectrum expanded modes in ansys apdl ?

Hello, When i am performing response spectrum analysis i am choosing 12 modes to expand but this message appears: ,How can i solve it ? thank you,

31 December 2018 2,092 3 View

Problem with shell element smeared reinforcement in ansys apdl?

How are you? I am trying to model reinforcement to shell181 element in ansys apdl by using this command: !* sect,2,reinf,smear,rft secdata, 3,628,200,0, 0.0,ELEf,3,0.5 ALLSEL,ALL ereinf But...

31 December 2018 4,929 1 View

Is it possible to obtain bending moment on model has been established using solid element 65 in ansys apdl ?

How are you? I made the model using solid element concrete 65 but it has 3 DOF displacement only ,is there any method to show bending moment in the program (as example depending on stress value we...

31 December 2018 7,538 2 View

How can i model smeared reinforcement in ansys apdl ?

please, I am trying to define smeared reinforcement in ansys apdl and it does not existing on the help i do not know why so i want to know the following: 1- is "area" one bar area or area of...

10 November 2018 5,594 0 View

IN ANSYS APDL How can i make grain material move from cylinder concrete to outside with assigned flow rate?

IN ANSYS APDL How can i give velocity to a material like grains to let it move from inside cylinder to outside to study the effect of flow rate on the concrete cylinder ( i mean i want to study...

10 November 2018 7,557 1 View

What are the steps to implement time history analysis method (nonlinear dynamic analysis)?

i want a good references to learn time history analysis from scratch, and how to implement it by steps (selecting and scaling ground motions) to get the structural response . thank you,

07 August 2018 6,647 2 View

What's the capacity of Ansys apdl command line?

I'm using command line code in "session editor" in ansys 13 instead of drawing with interface but i can't but code has more than 1870 lines so the rest i have to model it by interface and it's...

02 March 2018 8,218 3 View

How can i show model participation factor for modal analysis in ansys mechanical apdl?

please,How can i view modal participation factor after carrying out modal analysis in ansys apdl?. when i open the adjacent window of ansys to show output data not all of data appears. So i am...

31 December 2017 5,091 3 View

How can i import autocad file to ansys mechanical apdl?

I want to know How can i import autocad file to ansys mechanical apd. And the method to make cad file with any structure to import to ansys.

09 October 2017 266 4 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View