How can I see the changes in resonance with changing wavelength in MEEP?

04 April 2015 0 7K Report

Hi,

İ was wondering if we have a method, similar to parametric sweep in Comsol, in MEEP. İ want to see the resonance in microdisk change with wavelength that is off and on resonance.

Also I am confused about defining the source in MEEP. When we define gaussian source and provide central frequency, beam width (df) and no. of frequency points (n), does the program calculate the modes at each of these frequencies, if so where are results stored ?

Thanks

Badges
Science topic

More Hamza Humayun's questions See All

Modelling of scattering from gold hemispherical nanoparticle on substrate (COMSOL)?

Hi, I am trying to get scattering cross-section from gold hemispherical nanoparticle (r = 20 nm) placed on the Silicon substrate. I am attaching my image of the geometry. Substrate is being...

11 December 2019 341 5 View

Heating and cooling rates for annealing on metal nano islands formation?

Hi, In research papers, researchers mention the heating rates/cooling rates they used, for thermal annealing for formation of metal nanoislands (MNIs) after despostion of metal (using thermal...

03 April 2018 6,590 0 View

Plasmonic enhanced fluoresence (PEF)?

Hi, I wanted to clarify a few points about PEF phenomenon. 1. To observe the enhancement in PL setup, how important is the excitation wavelength of source? for instance if I am using AU NP around...

03 April 2018 9,990 4 View

Rapid thermal annealing?

How does RTA differ from furnace annealing in its science? For RTA, what parameters I can vary to stabilize the temperature? For instance, lets say I want to use RTA at 500 C under nitrogen...

08 September 2017 414 2 View

Any advice on the scattering from solutions?

I am confused and need help to get out of the mental block i am in. I am looking at scattering in solutions. In one case i have laser dyes in ethanol and also solution with liquid crystal as...

07 August 2015 1,329 3 View

Does anyone know how the 4X4 method is developed by pochi yeh for anisotropic media?

05 June 2014 3,964 8 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View