05 August 2020 5 924 Report

Hi,

I have seen reports using FEFLOW as groundwater model, that apply head boundary conditions in order to resemble artificial recharge (e.g. through infiltration ponds). Currently, I want to apply the same boundary condition in MODFLOW due to the luck of data regarding conductance etc. Is it possible to do that in MODFLOW-2005?

More Constantinos F. Panagiotou's questions See All
How to do a Welch's factorial Anova in spss?

I am doing a two way ANOVA in spss 27. However, the homogeneity of variances assumption is violated. Thus, I considered doing a Welch's factorial Anova but I cannot seem to find the way to do this...

31 December 2023 3,084 11 View

How to use temperature data and digital elevation model using co-kriging?

Hi, I have 26 sampling locations, relatively well distributed, but not adequately enough to cover the study area. I have also a digital elevation model, from which I can extract much more...

27 February 2023 4,252 2 View

Solving a bilevel optimization problem using evolutionary algorithms?

Hello, I want to solve a bilevel optimization problem using evolutionary algorithms for my research project. Can somebody tell me where can I find code for such problems?

29 May 2022 3,663 2 View

Are there any experimental data for the transition dipole moments of nucleic acids bases, preferably in the gas phase?

I am looking for experimental data, i.e., direct or indirect measurements of the transition dipole moments of nucleic acid bases and analogues. Specifically, of adenine, thymine, guanine,...

24 February 2021 6,740 0 View

Are there any statistical data on university students with disabilities drop-out rates?

Any research is highly accepted. Many thanks

05 August 2020 7,610 3 View

Why many persons are confused about the terms between inclusion and integration?

Some people believe that inclusion and integration are the same definitions. What is your viewpoint?

05 August 2020 1,447 6 View

Is the Applied Behaviour Analysis an appropriate method to teach individuals with developmental disabilities to protect themselves against COVID-19?

Any viewpoint is highly accepted! You can send any research papers or links which focus on this topic. Thank you all, C. Mantzikos

23 June 2020 7,917 9 View

Is there any research about COVID-19 and developmental disabilities?

Dear colleagues, Hope you are well and healthy and the work is going fine despite COVID-19. I need any research which focuses on COVID-19 and developmental disabilities. Especially I need some...

09 June 2020 7,876 11 View

Suitable channel model and beamforming technique for high band 5G?

Hello everyone, I want to simulate traffic in MATLAB between a multiple antenna base station and a single antenna user for mm-wave frequency of 28GHz. What is the most suitable channel model for...

20 March 2020 8,343 4 View

How to calculate the center of the main vessel using the contour?

Hello. I want to do some image analysis on OCT blood vessl images. Given the contour of the adventitia, how can I calculate the center of the main blood vessel?

19 January 2020 5,050 2 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close