How can I reduce a chemkin combustion mechanism and upload it in fluent?

Hemaizia Abd el Kader @Hemaizia_Abd_El_Kader

12 December 2018 0 3K Report

hello,well I'am try to simulate a premixed combustion using fluent in a part of this simulation I need to import a chemkin files with 25 reactions,can any one help me with this..?

regards

Badges
Science topic

More Hemaizia Abd el Kader's questions See All

How do I simulate a premixed flame in a combustor using fluent simulation?

i'm try to simulate a premixed flame in a adiabatic combustor and when i try to modeling i can't find how to input the mass fraction of species and how to declared the mixture in the same...

04 May 2018 2,130 0 View

I want to ask about how to calculate reynolds number of a mixture

hello,I want to calculate the Reynolds number of a premixed combustion of propane-air mixture, I used the mean value of Kinematic viscosity of two fluid to calculate Reynolds but I fined a wrong...

01 January 1970 7,521 4 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

Why aren't primary MHD generators with tokamak/stellarator configurations studied/researched?

Magnetohydrodynamic generators are normally used as eihter an attachment to recycle wasted heat and flow of other generators, or used to absorb the energy from rocket thrusters. However, I'm...

24 June 2024 3,949 1 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View