Can the methylation level of cultured cells/extracted DNA change?

15 November 2017 1,197 4 View

How to compare two kinds of plants to salt stress tolerance

28 August 2016 8,368 12 View

How to impose displacement load on the structure in ABAQUS?

30 July 2016 5,975 14 View

Why impedance on bare gold electrodes decrease with time?

I want to measure impedance between two bare gold electrodes in a PDMS micro-channel. The results (please see the figure) were scanned one after another with a time interval of few seconds....

09 April 2016 5,932 3 View

Why are qPCR amplicons about 100bp?

Why are qPCR amplicon about 100bp? Can PCR products improve the sensitivity of PCR? PS: I do amplify the 16S of environmental sample.

28 February 2014 7,816 6 View

Wetland delineation by remote sensing

What is the most suitable band or band combination for delineating wetland from upland?

12 August 2013 4,230 4 View

How to extract high quality DNA from sediment sample?

I extract DNA from the sediment sample, but the ratio of 260/230 is much lower than 1.7. I use the Nanodrop to measure the ratio. I use some methods such as cold ethanol washing or phenol...

18 June 2013 1,842 5 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is the best place in the world for the plant biotechnology research?

I am searching for a good place for the Post Doc,

02 March 2021 4,053 3 View